Thread: Which Multitool Linisher Attachment?

I have an original AU made unit.. 50 X 915.... it is rare for me to use the top, and generally only use the end where the roller is.... I never use the round disc either for that matter...

I buy my belts from the "sandpaper man" who advertises here on the WW forums.

I use the very coarse blue belts for ripping off the black oxide coating on steel, but finer belts for getting a smoother finish...

I do not use it for sharpening things, preferring a more solid wheel for that.. But exceptionally good for deburring and other general duties.. I would not be without mine..

I can get you what grits I use tomorrow...

Thanks RC. According to the H&F website they are still made in Oz.

jack620
I have the 915x50 which I use to clean up welds,round corners,take off sharp edges etc. I use mainly 60 grit belts and scotchbrite belts.I always wear the edges off the belt first,so the narrower belt is cheaper for me.It looks like you get about the same amount per dollar whichever length belt you buy.
John

Hi,
Mine is 915 x 50 and its nearly lasted nearly 20years . Its probably the most used tool in my shop.

Grit size for me is #80 for roughing and #240 for polishing.
If you buy multiple belts and live in a humid area don't buy too many at a time as the humidity affects the bond.

I have narrowly avoided a smack in the chops a couple of times.I have got to the point where I can "feel" its about to let go and step away.



Grahame

Thanks fellas. That's three votes for the 50x915.

This tool is on my bucket list to make or buy. In woodworking a longer belt path results in lower average belt temperature, but their belts are full contact, full bite. If you guys reckon less than a metre is OK then that's what I'll look for/plan on.

I just sold my disc sander, so this might have to bubble to the top of the list after Los Migración Mexicanos.

Ask RC

Originally Posted by Greg Q

This tool is on my bucket list to make or buy.

If you are shopping, the Bader style is worth considering... Stephen Bader & Co., Inc. - Manufacturer of quality belt grinders, polishing and finishing equipment

Regards
Ray

What, you don't have one Gred, how is that possible?

Another vote for the original 50 mm version with as many belts as you can muster. I use all grades of scotchbrite and zirconia belts, with each having its own purpose. I think the 100 mm version is probably better suited for woodworking. I agree, I don't use the table much and find it a bit whimpy at times. I keep forgetting to make up a 90 degree fence for it until next time I go to use the table, but would definitely find it more useful if it was on there.

Overall, chances are, if I'm in the workshop for more than one hour, I will use this tool at least once in that time.

Pete

I will echo the sentiments expressed above - I love my 50 x 915 for shaping, cleaning up and deburring. Grits for those uses could be anything from 40 to 120. Grab a couple each of a few different ones and have a play. If you have trouble with vibration I can help with a quick easy balancing procedure.

I have a 50X915 Multitool on a 1/2 hp grinder which gives good service. I have a mate that has a 50X1220 (not sure of the HP) that I have use a lot and (I Think) it is able to remove metal faster! With a 3/4 hp grinder to put it on I'd go for the 1220 linisher. I thought the drive pulley of the 1220 was a slightly larger diameter, but I may have that wrong?
Graeme

Another vote for the 915x50, i have 2 actually.......One of mine is on the wrong side of the grinder, so i can see what i'm doing when using the flat plate, the other is the right way up.
Honestly i wouldn't bother with the 1220, if you need more than the 915, i would go up to a radius master or Bader machine. You could probably pretty easily extend the 915's anyway, if you really wanted the longer belt.

I have 2 multi tool linisher/belt grinders all are 50x1220 one is 70mm the 200mm/8", 50x1220 belts last longer and run cooler, especialy when using the 8" contact wheel, I have have one of my units for 20 odd years and use it all the time, it runs on a 2hp motor it has never had a fault, as for belts I use many different types what ever suit the job

Originally Posted by Pete F

What, you don't have one Gred, how is that possible?

Another vote for the original 50 mm version with as many belts as you can muster. I use all grades of scotchbrite and zirconia belts, with each having its own purpose. I think the 100 mm version is probably better suited for woodworking. I agree, I don't use the table much and find it a bit whimpy at times. I keep forgetting to make up a 90 degree fence for it until next time I go to use the table, but would definitely find it more useful if it was on there.

Overall, chances are, if I'm in the workshop for more than one hour, I will use this tool at least once in that time.

Pete

I don't know why, but the linisher has passed me by. I feel as though I am the last member of some forgotten cargo cult*, languishing in my pre-linisher ignorance. I have coconuts aplenty, but they are all hairy and rough. Now if only I had some means of streamlining these things I feel that I could be making some progress. Sigh.

*remember those guys? No, me neither.

Gred, which sound like a good moniker for Shrek's more ploddish half brother. I may have to start picking my nose. Constantly.

One more for the 915 x 50. I use the blue belts, 60, 80 and 120 grit seems to get me by.

My brother gave me mine when he moved to Melbourne just over a year ago on a nice abbot and ashby grinder. Now I don't know how I did without it.