Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: help needed!!!!!
-
8th August 2010, 01:40 PM #1
Now totally retired...........
- Join Date
- Jan 2008
- Location
- sydney
- Age
- 78
- Posts
- 527
help needed!!!!!
Hi All
I posted the following in the woodturning forum where I normally lurk and one of our senior members sugested I post it here....... any help would be greatly appreciated
Hi have just got the parts from Trend to set up the Cougar for out board turning I have opted to mount an 18" bed extension on the stand and make a leg to go from the end of the extension to the ground this will give me 400mm over the bed (more than I can handle at this time)>. I have a second banjo that will live on the extension the only problem is I need to extend the height of the banjo with an adaptor....... So Is there some one out there that could make the adaptor as per the atached drawing
Happy to pay just need the damed thing
Regards
Bowl Basher
I can turn large lumps of wood into very small bowls
-
8th August 2010 01:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
8th August 2010, 01:43 PM #2
GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
I can,what part of Sydney are you in.
-
8th August 2010, 01:56 PM #3
GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
I'll do it If you can't get someone in Sydney to.
I have no idea what you are talking about it doing.
Tolerances?(I assume the 25's need to be pretty close, the shaft a little under the bore a little over)
Is it going to spin?(do the center lines of the bore and the shaft need to line up?)
Does the bore need to have a flat bottom?
Material will cost something like $25(mild steel. Assuming the 50mm can be a little under)
Does it have to be 3/8 thread or will the nearest metric do?(I'm not sure I have a 3/8 but will check)
Stuart
p.s. nvm then. wow I must type slow lolLast edited by Stustoys; 8th August 2010 at 01:58 PM. Reason: coz pipeclay beat me
-
8th August 2010, 03:05 PM #4
Now totally retired...........
- Join Date
- Jan 2008
- Location
- sydney
- Age
- 78
- Posts
- 527
Hi Pipe clay
Originally Posted by pipeclay
I am In Dundas ( near Parramatta )
Thanks
GrahamI can turn large lumps of wood into very small bowls
-
12th August 2010, 06:45 PM #5
Now totally retired...........
- Join Date
- Jan 2008
- Location
- sydney
- Age
- 78
- Posts
- 527
Hi All
Thanks to pipe clay My new outboard system is up and running .. the tool post extension he made for me is just perfect . the shiny bit is pipe clays work .......
Thanks again
Bowl BasherI can turn large lumps of wood into very small bowls
Similar Threads
-
4WD needed
By woodnut in forum MOTOR VEHICLESReplies: 5Last Post: 9th April 2010, 11:43 PM -
ID Help needed !
By gawdelpus in forum WOODTURNING - PEN TURNINGReplies: 11Last Post: 6th May 2009, 09:04 AM -
Help needed with an AL-54B
By funkychicken in forum METALWORK FORUMReplies: 1Last Post: 26th March 2009, 04:46 PM -
help needed plz - info needed on turning tools
By theyoungster in forum WOODTURNING - GENERALReplies: 5Last Post: 7th August 2007, 02:31 PM -
Help needed
By ozwinner in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 16Last Post: 13th May 2004, 12:00 AM
