Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Hercus Mill
-
4th May 2009, 09:38 PM #1New Member
- Join Date
- May 2009
- Location
- Perth
- Posts
- 6
Hercus Mill
Hi all,
I am in Perth WA and have a model O which i am selling.dont know if this is the right section to be putting this as i am new to the forum?
-
4th May 2009 09:38 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th May 2009, 11:49 PM #2.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Hello PBrown,
You wouldn't, by chance, have the slotting head for the mill laying around and want to sell it separately?
I look forward to hearing from you.
Regards Bob.
-
6th May 2009, 12:01 AM #3New Member
- Join Date
- May 2009
- Location
- Perth
- Posts
- 6
Slotting Head
Hi Bob,
Answer is no, i dont have one.It comes with the horizontal and vertical attachment only.What sort of work do you use your mill for?
Peter
-
6th May 2009, 12:10 AM #4Simsy
- Join Date
- Jun 2001
- Location
- Perth, WA (Ellenbrook)
- Age
- 73
- Posts
- 430
Hi Peter
What are you asking for your mill?
-
6th May 2009, 12:20 AM #5New Member
- Join Date
- May 2009
- Location
- Perth
- Posts
- 6
Model O
Hi Geoff,
$1900.00 Itsin very good condition and has new clamp set,slotting,slitting facing blades for the horizontal and a MT3 arbour for face mill and a 75mm new vice and a complete face mill cutter.It is also 3 phase.
Peter
-
6th May 2009, 01:04 AM #6.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Hello Peter,
If you proceed to the Hercus Area section, there is a thread called "Hercus User Names".Scroll down and you should find some photos of my garish blue mill at work. I had purchased a Hercus tool and cutter grinder vise body on Ebay and decided to make the base to suit the mill. What you see started off as a slice of 8 inch round cast iron bar.
The rotary table is a Hercus item. I obtained the casting from Hercus a couple of years along with the eccentic worm spindle. These were the only parts available. The table is another slice of 4E cast iron, the worm gear and worm wheel I purchased from England. The table was originally supplied with the division plate and sector arm off the dividing head, the graduated collar is something I made up to make it a bit more convenient to use. The dimensions of the table top are based on a scaled catalogue photo.
I guess what I have been using the mill for is to make the accessories and attachments that I can no longer buy for it.
Regards Bob.
Similar Threads
-
Hercus mill bearing lubrication.
By SurfinNev in forum THE HERCUS AREAReplies: 7Last Post: 13th March 2009, 12:32 AM -
Hercus Oil
By Mark2 in forum THE HERCUS AREAReplies: 6Last Post: 3rd March 2009, 11:58 AM -
No. 0 Mill Serial Number and Mill at Work Photos
By Anorak Bob in forum THE HERCUS AREAReplies: 1Last Post: 30th December 2008, 03:31 AM -
Hercus parts on Ebay from Hercus
By bollie7 in forum THE HERCUS AREAReplies: 0Last Post: 8th October 2008, 02:59 PM -
Comparison Between C.S Mill & Bandsaw Mill
By echnidna in forum SMALL TIMBER MILLINGReplies: 2Last Post: 7th October 2007, 04:26 PM