Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: Lathe motor problem
-
20th October 2012, 10:34 AM #1Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Lathe motor problem
When starting, after standing idle for awhile (overnight), the motor on my lathe runs very slowly for around 10 seconds+ before hitting top speed, after successive start ups, the delay shortens to around 3-4 seconds. I’m hoping/guessing it’s a capacitor. Any ideas?
-
20th October 2012 10:34 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th October 2012, 11:00 AM #2
-
20th October 2012, 11:50 AM #3Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Which one?
I'm guessing the starter cap is the one with the highest value? TOSS?
-
20th October 2012, 01:37 PM #4
-
20th October 2012, 02:10 PM #5Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Nope
Nope, I have the Al250G. But never heard of a Toss.
-
20th October 2012, 02:25 PM #6
So I guess that means you couldn't give a TOS?
It's all part of the service here at The House of Pain™
-
20th October 2012, 02:31 PM #7
-
20th October 2012, 04:16 PM #8Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Toss-er
You've probably just heard some refer to me as that Toss-er. Anyway, just did some more checks: with the belt off the motor starts fine and all the connection are ok, so I guess that cinches the deal, need a new start cap! There was another forum member who bought an AL250G, his caps blew up - spectacularly.
-
20th October 2012, 07:22 PM #9Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Depending on temperature, it could be related to bearings and/or lubricant needing to warm up. If you took the belts off and it was fine then it could be that. I used to have that issue on a Dai-shin lathe that I had once.
Michael
-
20th October 2012, 08:07 PM #10Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Best Bet
Maybe, I’ll replace it anyway just to make sure it doesn’t go at an inopportune time, just have to find someone who stocks them. I call it ‘Tongleh’s Law’, plenty of experience with that one.
-
21st October 2012, 03:05 PM #11GOLD MEMBER
- Join Date
- Aug 2011
- Location
- Melbourne
- Posts
- 2,951
Hi there,
Ebay sell starter caps. Quite a few sellers last time I looked. OR, it could be a good excuse for a DC or 3 phase VFD conversion. No starter caps needed!
Simon
-
21st October 2012, 05:00 PM #12Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Vroom, vroom.
I never thought of looking on eBay, but will do now. I could look at a DC motor and VSD I suppose, imagine the possibilities: a VSD and a geared head… Vroom, vroom.
Similar Threads
-
Motor problem: Bosch GCM 12 SD Professional
By Mitre Saw in forum GENERAL & SMALL MACHINERYReplies: 6Last Post: 25th August 2012, 02:09 PM -
Omga Radial Arm Motor Rewind problem
By TerryOz in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 5Last Post: 27th March 2012, 04:14 PM -
Motor problem
By Malcolm Eaton in forum TABLE SAWS & COMBINATIONSReplies: 4Last Post: 18th November 2010, 08:47 AM -
Tablesaw motor problem
By sundancewfs in forum TABLE SAWS & COMBINATIONSReplies: 14Last Post: 7th August 2008, 12:29 PM -
Motor Tension Problem
By Jim Grant in forum BANDSAWSReplies: 1Last Post: 3rd August 2005, 12:18 AM