Page 3 of 6 FirstFirst 123456 LastLast
Results 31 to 45 of 87
  1. #31
    Join Date
    Dec 2007
    Location
    Melbourne
    Posts
    3,277

    Default

    Any of you guys had to cut down long blades to fit your saws?? I'm trying to fit so 18" blades to my 15" saw. Cutting is no issue but u can't put a new hole in the blade. tried grinding the hole, drilling with a masonry drill. All went no where
    …..Live a Quiet Life & Work with your Hands

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #32
    Join Date
    Aug 2003
    Location
    Conder, ACT
    Age
    77
    Posts
    6,051

    Default

    Try a cobalt drill bit.

  4. #33
    Join Date
    Oct 2004
    Location
    Southern Highlands NSW
    Posts
    920

    Default

    Try regrinding the masonry drill with a positive rake, otherwise you're just trying to friction cut a hole.
    It worked when I shortened a power hacksaw blade recently.
    Sometimes the brazing that holds the tungsten carbide to the drill can get too hot and melt, so go easy.

    Jordan

  5. #34
    Join Date
    Dec 2007
    Location
    Melbourne
    Posts
    3,277

    Default

    DSC_0252.JPGDSC_0251.JPG

    Yep i'll take it easy on the next one…….
    …..Live a Quiet Life & Work with your Hands

  6. #35
    Join Date
    Jul 2006
    Location
    Canberra
    Posts
    414

    Default

    Spaulder, about the dashpot (the hydraulic cylinder), I guess you probably already got it apart, but I'll just say that mine was pretty hard to get off. It is a press-on fit, and tapping around the rim of the lid slowly gets it off. I put in a piston I made of a piece of Austlon C100 (oil-filled caprolactam nylon, from the local industrial supplier) (about 1/4" length of 28mm dia that I turned to fit the cyinder. I can't remember what else I did to get the dashpot working - some sort of adjustment I guess - I have a vague memory of a perforated metal disc in there that is adjusted somehow to let oil through at a chosen rate - whatever I did, it must have been straightforward because it works just right, I'm no mechanical genius and there was no instruction manual!

    Maybe take a pic when you have the dashpot apart, I'd appreciate it as it might refresh my memory.

    As to the blade, if you can find this on eBay, it is the right length (fits straight on) and I think the right nr of teeth/inch:
    Starrett RS1214-5 12" x 1" (300mm x 25mm) 14T

    A new blade will grab on any sharp edge (e.g. angle iron) and then shatter, so cut a pipe or some rod to break it in.

  7. #36
    Join Date
    Oct 2011
    Location
    sydney
    Posts
    880

    Default

    I took some photo's of the dashpot today. Hope they help.
    I'm hoping by refilling it with oil it'll work.
    Ben.
    Attached Images Attached Images

  8. #37
    Join Date
    Dec 2007
    Location
    Melbourne
    Posts
    3,277

    Default

    What grade of oil are you planning to use?? I imagine the grade or viscosity will have a stronger effect here than in an engine as in this case it won't heat up from the motor to become more fluid.
    …..Live a Quiet Life & Work with your Hands

  9. #38
    Join Date
    Oct 2004
    Location
    Southern Highlands NSW
    Posts
    920

    Default

    It's great to see those photos, Ben.
    I've filed them for when the time comes to do mine up.

    Jordan

  10. #39
    Join Date
    Oct 2011
    Location
    sydney
    Posts
    880

    Default

    Hi,

    Not sure what grade of oil, whatever I can find at the time.

    I'm glad I took the photo's, it's been a long project and it's going to get longer. I have to head up to Townsville for two months starting in October. No way I'm going to remember where everything goes. I'm hoping to get the base back together this week.

    Ben.

    ps, I have a lot more photo's on my phone that I haven't posted in you want them.

  11. #40
    Join Date
    Aug 2008
    Location
    Adelaide
    Age
    68
    Posts
    834

    Default

    Quote Originally Posted by bwal74 View Post
    Hi,
    I'm glad I took the photo's, it's been a long project and it's going to get longer. I have to head up to Townsville for two months starting in October. No way I'm going to remember where everything goes. I'm hoping to get the base back together this week.

    Ben.

    ps, I have a lot more photo's on my phone that I haven't posted in you want them.
    Yes please, I've bought a Lotze which is on the round-tuit list....

  12. #41
    Join Date
    Jul 2014
    Location
    Sofala
    Posts
    7

    Cool Lotze power hacksaw

    Hi I too have acquired a trusty lotze unfortunately no motor any idea wat hp and speed they had installed ?Just starting to clean her up apart from motor all complete Thanks in advance Freefall1

  13. #42
    Join Date
    Jul 2006
    Location
    Canberra
    Posts
    414

    Default

    Just a few replies I've been meaning to get onto about the Lotze, re: dashpot, motor, and the 'disc-thingy' mentioned sometime ago:

    1. Dashpot. Ok, so I just took mine apart to see what I did. See photo below. The original metal piston with holes around it was too loose in the cylinder, so the oil would just bypass the piston and the saw frame would fall very quickly. To fix this, I turned a thin (3mm approx) disc of nylon (I used Austlon 100, but it could be anything nylon e.g. old breadboard I think, after all it is bathed in oil so does'nt need self-lubrication). The diameter is to fit the daspot cylinder, so on mine the nylon disc is 25.35mm dia. Yours will be to suit your own cylinder. The hole in the centre of the disc is drilled larger than the 5/16" (~8mm) spindle it fits over, maybe drilled 10mm, because you want it to self-centre when riding up and down in the cylinder. You'll see in the photo that the oil level is about half full. If you put more in, it will just ooze out through the air hole in the lid (air hole has a small screw in it for adjustment) and make a mess. The oil is nothing special. I can't remember what I used, but I guess it was gearbox oil, because that's what I have around. In action the oil is not doing heavy duty, it's just oozing through the holes around the metal piston, it's not a big deal. To adjust the rate of fall, you adjust the nut below the spring on the spindle to set the spring tension. Mine is set about as loose as it can be (the nut is right at the end of the spindle). I get a nice slow fall of the saw frame, that's what I want.

    2. Motor. The motor is 1/4 horsepower 1425 rpm. A McPherson 'Cadet', made by GMF, all of a bygone era. Goes fine. It has a big frame for that low horsepower - the body of the motor is about 6.5 inches diameter. In the photos you'll see the chassis that supports the motor at one end and has a cast-in bearing housing at the other end. Hopefully you have that at least. In getting a new motor, there might be a temptation to go for more power - e.g. to get a 1/2 or 3/4 hp motor, after all with smaller modern motor frames they would probably fit ok. But I would advise against it. The 1/4hp is certainly powerful enough, and if anything goes wrong (like anything eventually unscrewing itself with all the vibration that goes on) it is forgiving. Any extra horsepower might do some big damage. I'm not keen on the flex power cord loosely wending its way through the works - I keep having visions of mounting a switchblock on the heavy cast frame-stand just outside the motor, but hey, it works as-is and I'll probably never do it. But for those who are still to do the big restoration and have the momentum, that would be the go I reckon.

    3. Disc-nut under the swivel vise. This photo should be self-explanatory, its just to show where the 'disc thing' goes. That block of wood, well, its a bit embarassing that I haven't made something nicer. The wood is jammed in between the top of the motor and the underside of the bed. It stops the motor bouncing up and down as the saw does its work. Originally I had a nicer wood block in there, I swear your honor, but it fell down behind the motor. I can't fish it out, so I just grabbed the closest damn block of offcut I could find and jammed it in there instead. So it has stayed to this day, out of sight, out of mind.

    Ian


    DSCF2626.jpgDSCF2630.jpgDSCF2631.jpg

  14. #43
    Join Date
    Oct 2011
    Location
    sydney
    Posts
    880

    Default

    I have the same motor. Works fine. Not sure about my dashpot, it had no oil in it so I don't know how it goes yet.

    I've started to put the base back together, you think it would be easy. Lucky I took photo's.

    Cheers Ben.

  15. #44
    Join Date
    Oct 2011
    Location
    sydney
    Posts
    880

    Default

    Hi,

    Still going. Started to put the base back together. Wish I had of taken more photo's. Getting the casting base (the biggest casting) securely onto the base has got me stumped.

    Ben.
    Attached Images Attached Images

  16. #45
    Join Date
    Jul 2006
    Location
    Canberra
    Posts
    414

    Default

    Ben, I'm pretty sure that when I put mine back together, I started with the two end stand castings and the bedplate casting, and bolted them together first, before filling the space with the motor chassis and motor. I have a vague memory that you also need to assemble the full superstructure onto the bedplate (crank bearings and saw frame) before dealing with the motor chassis and motor, because there's things you need to reach from underneath I think - but my memory is foggy now. I didn't put the side plates on until right at the end of the whole assembly process. By leaving the motor and side plates until last, I had unimpeded access to the insert and tighten the bolts that hold the bedplate. Maybe you have problems accessing the bolts because the motor and motor chassis are in the way.

    Ian

Page 3 of 6 FirstFirst 123456 LastLast

Similar Threads

  1. Power Hacksaw
    By Auskart in forum METALWORK FORUM
    Replies: 4
    Last Post: 4th September 2011, 09:37 PM
  2. Hercus power hacksaw
    By Gavin Newman in forum METALWORK FORUM
    Replies: 12
    Last Post: 14th October 2010, 08:51 PM
  3. Power Hacksaw pics.
    By Woodlee in forum ANTIQUE AND COLLECTABLE TOOLS
    Replies: 46
    Last Post: 4th August 2009, 12:46 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •