Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Machinability of 6060 aluminium?
-
23rd May 2014, 01:09 PM #1SENIOR MEMBER
- Join Date
- Jan 2004
- Location
- Bellingen
- Posts
- 587
Machinability of 6060 aluminium?
Anyone had any experience machining it!
It's a fairly simple job. I need to make water cooled plates.
The two plates are 160mm by 6mm by 800. I was planning on machining a 2mm ( ball nose) matching track, putting in a gasket and bolting them together. Then plumb in the inlet/outlet barbs.
I'm guessing sharp hss with WD40 in the Mill is the go or is it just too gummy?
It is classes as 'fair' machining but that really does not say a lot.
-
23rd May 2014 01:09 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd May 2014, 01:26 PM #2
I find with any ally chip removal is key. If they hang around they can get hot and i have had them melt on to cutters. I normally spray some WD or kero on the piece first then use air to clear the chips as it cuts. I have had zero experience outside plain ally though.
Ew1915 17"x50" LeBlond heavy duty Lathe, 24" Queen city shaper, 1970's G Vernier FV.3.TO Universal Mill, 1958 Blohm HFS 6 surface grinder, 1942 Rivett 715 Lathe, 14"x40" Antrac Lathe, Startrite H225 Bandsaw, 1949 Hercus Camelback Drill press, 1947 Holbrook C10 Lathe.
-
23rd May 2014, 05:47 PM #3GOLD MEMBER
- Join Date
- Oct 2010
- Location
- melbourne, laverton
- Posts
- 1,469
ally
ethonol works as a cutting fluid. carbide is great to
-
23rd May 2014, 06:01 PM #4SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- sydney
- Posts
- 880
I use kero in a spray bottle or WD40 if I can reach it first.
Ben.
-
23rd May 2014, 06:14 PM #5future machinist
- Join Date
- Mar 2008
- Location
- nowra
- Posts
- 1,361
I use inox as a lubricant I agree with Ueee use air to clear the chips
BETTER TO HAVE TOOLS YOU DON'T NEED THAN TO NEED TOOLS YOU DON'T HAVE
Andre
-
24th May 2014, 01:24 AM #6
I use kero as well ! I apply it with a brush and brush the chips away since I've no air supply... Yet !
Best Regards:
BaronJ.
-
24th May 2014, 09:22 AM #7SENIOR MEMBER
- Join Date
- Jan 2004
- Location
- Bellingen
- Posts
- 587
Nice one fellas! I will give it a go then.
I'm changing it up a little and cutting up a gasket to make a track. It's a much larger surface area and a whole lot faster to make. But I will still need to chop it all up and dress the edges.
Actually, I have to cut the stock to suit. I'm thinking an aluminium cutting blade on the table saw to rip it to size. My neighbour has a 'dual saw' I might borrow. It comes with lube sticks for cutting ally. I can't bring myself to buy one as this is the first time I think I could have used it...they seem a little Mickey Mouse to me.
-
24th May 2014, 11:37 AM #8GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
6060 will machine fine, just keep the chips out of the way as others have suggested.
As far as lubricant goes, CRC/Inox/WD40/Kero and possibly Diesel would be fine as is soluble oil/water mix. I add Diesel as it is cheaper than Kero and I reckon its properties should be similar, plus I like the smell of it.
Something to watch out for with the machinable grades of ally, is the fact that many are not weldable. A past employer of mine found that out the hard way, having invested a large amount of time welding hinge bosses into the bow doors of a car ferry, only to have them crack out as they cooled. Several $1000 later, new bosses made, old ones removed, new ones welded in.
-
24th May 2014, 06:49 PM #9
Hi Ben,
FWIW I often use my 10" 80 tooth TC table saw to cut aluminium, both sheet and bar. I've cut 20mm thick sheet and 4" round bar on mine. It runs at 2800 rpm and requires wax or some other lubricant. Just take it steady and don't push it too hard. What happens is the alloy expands very rapidly and grabs the blade if you do. This stalls the motor on mine, which unless you get it switched off pretty quick will rapidly burn out the motor.Best Regards:
BaronJ.
-
24th May 2014, 08:47 PM #10SENIOR MEMBER
- Join Date
- Jan 2004
- Location
- Bellingen
- Posts
- 587
Bloody good point Baron! I didn't think of that.
I have four 6mm plates I have to rip down to 150mm from 160mm. I might be lucky and it will warp away from the kerf...maybe. I will take some care with it now though!
Similar Threads
-
Machinability of MIG weld
By Bryan in forum METALWORK FORUMReplies: 14Last Post: 27th March 2013, 11:14 PM -
aluminium
By SHIPPERS in forum METALWORK FORUMReplies: 3Last Post: 30th April 2012, 03:06 PM -
aluminium
By Ash240 in forum METALWORK FORUMReplies: 3Last Post: 28th October 2010, 11:55 AM -
Aluminium
By catbuilder in forum WELDINGReplies: 20Last Post: 4th January 2009, 07:48 PM