Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 36 of 36
-
3rd April 2014, 04:07 PM #31
Hi RC,
Nice looking piece of iron... I can see all sorts of useful jobs that would fit nicely on that... what's the capacity?
Ray
-
3rd April 2014 04:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd April 2014, 06:56 PM #32Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Ray the table is 24X24... Cross slide travel is 30 inches, vertical travel on this machine is 36" as it has a 12" extension, and I believe longitudinal travel is 30 inches... Traveling spindle travel is said to be 26 inches in two stages of 13 inches... Facing head is 16" in diameter, top speed is 400rpm.. It is a 1942 made machine.. 5hp main motor with forward reverse clutch..
You can see a lot more photo's over here where the G&L #25 self help group is located http://www.practicalmachinist.com/vb...ml#post2265282
Here is a couple of vids on youtube of the table version of this machine (no rotary table)
https://www.youtube.com/watch?v=bV1E...GdYtJ_JIGLq8hw
https://www.youtube.com/watch?v=9M6c...GdYtJ_JIGLq8hwLight red, the colour of choice for the discerning man.
-
6th April 2014, 09:12 PM #33Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
-
7th April 2014, 12:03 PM #34Senior Member
- Join Date
- Apr 2009
- Location
- Ballina N.S.W.
- Posts
- 371
Hi Richard,
The machine looks good cleaned up and sounds great,are they levelling screws on the base that I thought were hold down bolts?
Bob
-
7th April 2014, 02:37 PM #35Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Yes they are levelling screws, but they are hollow, and the hold down bolts go up through the middle of them...
The gear box is dead quiet at low RPM, except for the clutch.... It has a rattling noise in there, which I am guessing is a worn clutch fork... It sounds like one very worn bearing up in the head where the drive shaft is.. I would say it will be a plain deep groove ball bearing.. Should not be hard to get to depending on how hard the vertical drive shaft is to remove..
A lot of the noise also comes from that big steel belt guard vibrating and acting like a drum...
I measure the wear in the bed to be less then 0.1mm.. So it would be within my capabilities to rescrape the bed ways should I feel the need... Another reason why I went after this machine, being that reconditioning the ways would be feasible for me to do here...
Overall I am happy with it... I know I paid more then it is worth, but value is int he eye of the beholder.... As an added bonus the person that lifted it into my shed, wants to buy my Hercus 260, which I was selling anyway now that the 10EE is going...Light red, the colour of choice for the discerning man.
-
7th April 2014, 04:13 PM #36SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
This is what happens to nice blokes Richard.
By the way did I thank you for the bandsaw clamp you made...
Phil
Similar Threads
-
Milling machine instruction required
By neksmerj in forum METALWORK FORUMReplies: 5Last Post: 13th August 2013, 08:03 PM -
Training on cnc machine required
By rafa in forum WOODWORK - GENERALReplies: 1Last Post: 18th July 2009, 06:19 PM -
Cabinet maker/handyman required to cut & machine MDF (Melb)
By themitrededge in forum EMPLOYMENTReplies: 0Last Post: 2nd July 2009, 02:24 PM -
Washing machine motor, help required.
By jaguarrh in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 30Last Post: 21st March 2009, 08:41 PM -
Mortising Machine - Help Required
By Rsup in forum WOODWORK - GENERALReplies: 1Last Post: 3rd October 2007, 12:02 AM