Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 23 of 23
Thread: Macson Double Ended Grinder
-
21st September 2013, 02:24 PM #16SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
-
21st September 2013 02:24 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
21st September 2013, 07:55 PM #17
I agree with .RC. He's got a pink lathe so he would not speak with forked tongue .
Dean
-
7th October 2013, 02:23 PM #18Senior Member
- Join Date
- Nov 2007
- Location
- mid north coast NSW
- Posts
- 148
Graeme Thanks for the info, 1937...wow, didn't think it would date back that far. Any chance you could scan the page for me.
I haven't checked the motor plate yet, so it will be interesting to see if it is 2HP (I will check that tomorrow). The tool rests definitely aren't original.
Camo[/QUOTE
Sorry I forgot to reply! More than happy to scan that page for you. Also I forgot to mention that in another cat.. I found an explanation of the two speeds ( may be I'm the only one that didn't know!!) The slow speed is for when the wheels are new and high speed for worn wheels!! I have worked in many shops with large grinders over the years and don't remember the speed ever being changed!? Graeme Edit Three markets in three days takes it's toll.
-
7th October 2013, 06:54 PM #19SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
-
7th October 2013, 09:23 PM #20GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
Camo, I've used several of these over the years, they can take off material and skin very quickly if you lean into it. DAMHIKT.
Make sure that the rest is kept close 2-3mm max. as I have had material grabbed and jammed in between the stone and rest in my younger days.
Kryn
-
8th October 2013, 12:12 AM #21SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
Kryn,
Thanks for the reply. Thanks for the heads up regarding the rest positioning. I am aware of the dangers, but it's always good to get a bit of a reminder, and I will be checking everything carefully before it goes into service, and I have some thick Perspex which I will be making some guards out of.
Cheers,
Camo
-
8th October 2013, 06:01 AM #22
-
8th October 2013, 09:29 AM #23Senior Member
- Join Date
- Apr 2009
- Location
- Ballina N.S.W.
- Posts
- 371
Camoz,
A great grinder you have, many years ago we had four of these in a non ferrous foundry business, ours were the 12" & 14" models. They sure can remove heaps of material and as Kryn has suggested make sure you have the tool post adjusted real close to the wheel 2mm and done up tight as they can snatch the work in a millisecond.These are serious powerful grinders. Always grind with a pair of fully shielded safety glasses /full face shield on as they put out a lot of dust and it builds up. If you do a lot of grinding clean out the buildup that collects on the back of the guard as it will eventually build up enough to fall off and it is like a bomb going off. I had to take quite a few of our workers to the hospital to have debris removed from their face and eyes over the years because they did not wear the safety gear or clean the buildup out. As to the bearings I only ever had to replace one in 20 years of constant use and I cannot recall the style. If it was my grinder I would do a bit more research and find out the correct one as you will only do it once and the machine will last several lifetimes.
Bob
Similar Threads
-
Double ended No. 1 Morse Taper
By Alby123 in forum METALWORK FORUMReplies: 8Last Post: 15th September 2012, 01:10 AM -
double ended bar
By david devine in forum SMALL TIMBER MILLINGReplies: 3Last Post: 29th May 2011, 07:48 PM -
double ended pen
By weisyboy in forum WOODTURNING - PEN TURNINGReplies: 3Last Post: 6th December 2007, 07:43 PM -
Double ended coach screws
By echnidna in forum WOODWORK - GENERALReplies: 4Last Post: 26th September 2005, 09:24 PM