Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
27th July 2015, 08:34 PM #1
Used MT2 shank drill bits or new straight shank
Guys,
I need a 19/32 and 3/4 drill bit. EBay has a few used Sutton MT2 bits and also new Sutton straight shank versions.
There is not a lot of difference in price.
The straight shanked versions have shorter flutes than the used MT2 versions.
My drill press has a MT2 fitting and so does my tailstock.
For the most part (99%) these drills will be used in the lathe.
Is there a difference in quality between the two variants?
My large chuck isn't brilliant (doesn't grip the bits that well) so I'm thinking the forces involved may sway me to the used variant... But then again I don't know how they've been (miss-)treated...
Which would you suggest?
Any thoughts?
Thanks
J
Thx
Jon
-
27th July 2015 08:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th July 2015, 09:12 PM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
What are you drilling? If its 6mm ply then the straights will be fine but if it's steel they would struggle.
-
27th July 2015, 09:28 PM #3
-
27th July 2015, 10:17 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
-
27th July 2015, 10:30 PM #5Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
You would expect that both being the same brand the quality of steel would be the same. I would personally go the MT2 route as I think they will hold better.
Are you going imperial for any particular reason? I have some duplicate metrics if that is of any interest.
Michael
-
28th July 2015, 12:52 AM #6Senior Member
- Join Date
- May 2012
- Location
- Kimberley, West Australia
- Posts
- 139
Drill choice.
You will need one drill for brass and another for steel unless you plan to re-grind each time. Best to trim the cutting edges back to a neutral or slightly negative rake for brass to prevent it from grabbing or behaving very badly. Makes for a smooth operation.
Combustor.Old iron in the Outback, Kimberley WA.
-
28th July 2015, 06:21 AM #7GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,645
-
28th July 2015, 09:00 AM #8SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Charlestown NSW
- Age
- 65
- Posts
- 899
Unless the used drills are obviously bent or are chewed up along the flanks than I'd be going for them. For the same reason that Michael as already stated. Theres always a risk that a used drill might have a slight bend in it that you cant see until you run it, but on one that size you would probably be ok.
If its a good quality drill, then theres not a lot that can be done to wreck it without it being blindingly obvious in the pictures, except for a slight bend.
bollie7
-
28th July 2015, 10:06 AM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
Similar Threads
-
hex shank drill bits & driver bits
By bryn in forum HAND TOOLS - POWEREDReplies: 3Last Post: 17th February 2015, 01:35 PM -
1/4" shank x 25mm+ cutting length straight bearing bits?
By d.m.s in forum ROUTING FORUMReplies: 7Last Post: 21st September 2014, 11:38 AM -
8mm and 6mm shank router bits
By KevinB in forum WOODWORK - GENERALReplies: 16Last Post: 1st April 2012, 04:24 PM -
Hex shank drill bits
By henlan77 in forum HAND TOOLS - POWEREDReplies: 0Last Post: 4th April 2008, 02:51 PM