Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 16
Thread: MT4 draw bar
-
30th October 2012, 03:54 PM #1GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,643
MT4 draw bar
My MT4-ER40 collet chuck turned up today. Now I need to make a 16mm draw bar to suit my hercus 260. The simplest idea I can come up with is a bit of 16mm all-thread, an aluminium bushing to fit the Hercus spindle, a washer and a 16mm nut.
My only concern is that there might be the potential to over-tighten the nut with the spanner and jam the collet chuck in the spindle forever. Just how tight should a MT be drawn into the spindle? Would a hand-wheel be better than a nut+spanner for tightening?
Chris
-
30th October 2012 03:54 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th October 2012, 04:03 PM #2Senior Member
- Join Date
- Jul 2012
- Location
- Griffith NSW
- Posts
- 257
I fail to see how overtightening will do anything other than strip the thread in either the collet chuck or the drawbar itself and in either situation, you just back the bar back out and belt it up the freckle until the taper separates, followed by repairing damage as necesary. Given the size of the collet, I would imagine that the job would spin in the collet before the MT4 started to spin, so I would think that a drawbar with a good sized handwheel ought to be enough.
-
30th October 2012, 04:25 PM #3GOLD MEMBER
- Join Date
- Aug 2011
- Location
- Melbourne
- Posts
- 2,951
Hi Chris,
My mill has an MT4 spindle. I find I only need to "nip" it up, if I tighten it any further then it's for no good reason and i find I that needlessly have to use excessive for with a hammer to release it. I find that just a gentle nip will give me all the take up I need (for my light duty work) and it then only requires a gentle strike with my hammer to release. A handwheel sounds like a great idea. Maybe something about 100mm in diameter would be sufficient, perhaps more if it was for a person with arthritic hands etc.... I like the idea of a spring loaded spindle lock and a drawbar release bolt, that way you don't have to hit the spindle at all. I have heard that with R8 you don't need to do that anyway
Simon
-
30th October 2012, 04:29 PM #4SENIOR MEMBER
- Join Date
- Jun 2012
- Location
- SA
- Posts
- 1,478
I do all my milling on my lathe using a Morse 4 ER32 collet with a similar metric thread draw bar. Thery are p#ss wasy to make and don't have to be anything exotic, just make sure they centre on the drive end - use a stepped washer or a cone.
A nut on the end of the draw bar works fine.
You would have to be a butcher to over tighten it.
You just nip up the bar lightly and when you want to remove it you tap on the end of the bar (nut) to knock out the Morse.
If you want to hit your flash handwheel with a hammer by all means go ahead, but I think you will find a nut is a better proposition
Also on a lathe with a drive belt cover, you can close the cover with a nut, but not a handwheel.
Cheers
Rob
-
30th October 2012, 04:47 PM #5GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,643
-
30th October 2012, 05:48 PM #6SENIOR MEMBER
- Join Date
- Jun 2012
- Location
- SA
- Posts
- 1,478
When you knock out the Morse taper I would recommend you turn the spindle slowly while you do it.
That way you are not hitting on the rear spindle bearing in the same position.
Obviously you tap lightly, but it's unwise to tap on a roller bearing in one position as you can mark the race.
Cheers
Rob
-
30th October 2012, 05:54 PM #7Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
A handwheel may have a fly wheel effect - that is, the handle wants to keep going when the spindle is slowing. This may tend to loosen off the drawbar. The taper will still be locked up so next time you start cutting you may get chatter or the spindle will start to slip.
I've made up some draw bars myself and would suggest that rather than a nut on the end of your all thread you work out the length that you need and pin the nut with a roll pin or similar. That way when you loosen the draw bar it's the arbor end that is loosening rather than the nut end. You could also turn a nut with the necessary conical base to save having a separate washer floating around. You only need 2 flats, so a bit of bar with a conical end, tapped M16 and then flats in the mill - easy.
Photo 4 shows the sort of thing https://www.woodworkforums.com/f65/sh...ml#post1425224
Michael
-
30th October 2012, 06:01 PM #8SENIOR MEMBER
- Join Date
- Jun 2012
- Location
- SA
- Posts
- 1,478
Hi Michael,
Yes I agree on both counts.
I've milled all day with some really big cutters and never had the draw bar loosen.
My draw bar has the nut bronzed on, so all the thread feed is at the Morse end.
A little dab of arc would suffice if you are not fussed about appearance
Those ER collet chucks are the bees knees. Just so damn easy to use and never get stuck or jammed.
Here's a photo of my setup. The flat centering washer is recessed into the end.
Cheers
Rob
-
30th October 2012, 08:43 PM #9GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,643
thanks for the pics fellas. They're a big help.
-
2nd November 2012, 08:10 PM #10Senior Member
- Join Date
- Sep 2007
- Location
- Newcastle NSW
- Age
- 77
- Posts
- 155
I have a mill with a MT4 spindle and I use a ring spanner from a Honda motorcycle tool kit to tighten the drawbar . The handle is only 100mm long.
I just give the handle a slight bump with the palm of my hand to tighten the drawbar. I only have to tap the end of the drawbar gently with my copper hammer to release it. My drill chuck socket has the tang end and to release it I drop a piece of 12mm rod (400mm long) down the spindle once or twice and it releases.
I have never had the sockets slip so it appears that very little tension is required to hold the Morse sockets securely.
Russell
-
3rd November 2012, 09:12 AM #11Senior Member
- Join Date
- Apr 2010
- Location
- Rural Victoria
- Posts
- 359
I use BT50 tooling in my 1936 Cincinatti 2M with an M25 allthread drawbar. The 'nut' is stepped for centering and has two flat faces on opposite sides so that I can tighten it with a shifter- just a gentle bump with the palm of the hand (against the inertia of the spindle) is enough to tighten or loosen the drawbar, and I release the taper with a gentle tap on the top end of the drawbar with a Huckson hammer.
I was a bit cheap in hindsight, and used only the standard (not high tensile) allthread at the time... nonetheless I cannot see any damage to the threads on the drawbar, even after many inspections.....
-
3rd November 2012, 09:29 AM #12GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,643
I've been wondering what type of all-thread to use. I guess the galvanised construction-grade stuff Bunnings sells isn't all that accurately cut? I reckon I'll just turn a 16mm thread on each end of a piece of 16mm BMS. I've got plenty of that. I will use a Bunnings nut though.
-
3rd November 2012, 09:40 AM #13GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Good luck with the bunnings nut most are like a co-k in a sock.
-
3rd November 2012, 10:33 AM #14GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,643
I just found some 16mm gal all-thread and nuts left over from when I built my house. It's not Bunnings stock, so the fit isn't too bad.
-
3rd November 2012, 01:11 PM #15Senior Member
- Join Date
- Apr 2010
- Location
- Rural Victoria
- Posts
- 359
I made the 'nut' from a piece of mild steel merchant bar (once again... bit cheap at the time) and cut the internal thread on the lathe. Now, merchant bar is crap, and I would have got a much better result had I gone to Lockbar and picked up a piece of BMS, for a lot less effort, but whatever you cut the thread from will give you a better fit than buying a 'nut' off the shelf. I then screwed in the allthread, leaving a gap, and filled it with weld with the MIG, ground it off and machined it smooth. Looks 'sorta' professional...
https://www.woodworkforums.com/member...7-cimg0157.jpg
https://www.woodworkforums.com/member...8-cimg0158.jpg
Edit: Just had a look at my own photos.... that is one sexy mill, even if I say so myself It has had a quick and lovely spray job (someone painted over the previous paint chips, and blue really isn't her colour...) I might get around to a sandblast and a coat of machinery grey...
Similar Threads
-
Draw bar pic
By Stustoys in forum METALWORK FORUMReplies: 3Last Post: 5th November 2010, 09:09 PM -
designing a draw for undermount draw slides
By SilverSniper in forum WOODWORK - GENERALReplies: 11Last Post: 20th October 2008, 08:17 AM -
Draw Knife
By BobL in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 9Last Post: 31st March 2008, 08:02 PM