Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
9th December 2011, 09:10 AM #1
What's The Active Ingredient in INOX MX3 Lubricant/AntiCorrosive
Hi guys
does anyone know what is the active ingredient(s) in INOX MX3, the lubricant/water dispersal agent/surface protection liquid, without causing upset to patent owners, manufacturers and agents?
Is it mineral oil, vegetable oil or lanolin based?
Has anyone had any long term (10yrs) experience with this product type as a metal surface corrosion protector against rust etc?
MSDS sheets shed little light on the subject, other than describing the propellants.
thanks
-
9th December 2011 09:10 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th December 2011, 09:27 AM #2GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
i'd say its Lanolin
most of their stuff is based around that
-
9th December 2011, 06:08 PM #3
Lanolin with a carrier few other things no doubt mixed in as well.
As with all of this stuff it depends on the application just to say is it good for corrosion I would have no doubt but if your close to the sea you may have to apply it more often then say if you were out west, give them a call I am sure they have some testimonials and a support line if they are any good.I like to move it move it, I like to move it.
-
9th December 2011, 06:22 PM #4GOLD MEMBER
- Join Date
- Mar 2011
- Location
- Dural NSW
- Age
- 82
- Posts
- 1,120
Inox
Mike
I do not know what the MX3 is, however I have been using Inox for a few years & find it very good.
I use it on all my tools for corrosion resistance including a lot of my precision cast iron woodworking planes as well as metalworking machinery & tools.
It seems to leave an oily coating on surfaces & for me its just been a total winner.
Aside from the normal uses I have found it works well on leather pump cup washers. I have a number of Coleman pressure lamps & the old kero blowlamps. Once I used the traditional "Neatsfoot" Animal Oil on these leathers cups, but found it tended to get gummy with time.
The Inox seems to work well & keeps these leathers supple & lubricated.
I noticed the Inox does not have any petroleum products in it.
regards
Bruce
-
9th December 2011, 06:28 PM #5Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
I stopped using it as a corrosion inhibitor on bright shiny machines surfaces as over time it dries and turns into a dark varnish like material that only comes off with a lot of elbow grease....
It stops the rust though and is hard to beat if you can put up with the dried material...Light red, the colour of choice for the discerning man.
-
9th December 2011, 06:35 PM #6Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 59
- Posts
- 2,557
Haven't used it myself but lanolin has a very distinctive odour, familiar to anyone who has been around shearing sheds.
If it's not mineral (petroleum) based it must be animal or vegetable.
-
9th December 2011, 09:32 PM #7
Fluid
Automatic transmission fluid is a good penetrant for rusty bits . MIKE
-
10th December 2011, 08:31 PM #8SENIOR MEMBER
- Join Date
- Mar 2010
- Location
- Nth Qld
- Posts
- 715
I heard it was a product or arrested or interrupted fermentation, you can make certain solvents like ethanol, acetone, propanol and other solvents through fermentation. Stopping the ferment through cold or chemically would give some intermediate chemical.
-
12th December 2011, 11:07 AM #9
I use a home made lubricant (for resizing brass for reloading) using a mix of lanolin (from the chemist) and metho (1:5 to 1:10). Also works great as a rust inhibitor.
Put it in a trigger spay bottle for easy application.Cheers.
Vernon.
__________________________________________________
Bite off more than you can chew and then chew like crazy.
Similar Threads
-
Active Users......
By Cruzi in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 0Last Post: 20th February 2008, 05:14 PM -
inox 36
By felixe in forum WOODWORK - GENERALReplies: 4Last Post: 5th May 2006, 11:29 PM