Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Cold Saw
-
2nd September 2012, 12:12 PM #1
Cold Saw
Most of my tools came to be with the "excuse" of a new project.
This time I am building a wrough iron balustrade that is on the large side. Almost 20 meters of it. Made of 25x25x1.6 tubing, the posts are 6x2 doubled up and railing are 6x2 timber.
The balisters will be grouped in panels of 5, separated by a larger gap devided with a square 12mm bar with a bit of a feature bashed in the center of it. The balisters will get a belting with a ball hammer so that they get a lot of dimpels all over them.
At 100mm spacing there is a lot of cutting and I couldn't see doing this either by hand or with the unbearable noise and mess of an abrasion cutter. In my days of apprendice blacksmith, this would have been "my" hacksaw job.
So I got myself a cold saw. It is the smallest and cheapest possible, a 275 metal master from Hares & Forbes. Made in Taiwan it is suprisingly tough and well made, at a bit over a thousand dollars, it is not cheap but it is a pleasure to use and works stright out of the box with no other set up than to screw in the stop for repating cuts and the stop for the elevation and mixing a liter of water with 50cc of cutting oil.
I have never used a cold saw before so I was very pleased to realise I don't need hearing protection, nor eye protection althoug I do use glasses anyway.
When you switch the saw on the motor is almost silent since it works in a worm gear box. The cutting sound is a grinding sound of low frequency that wouldn't bother the neighbours on a Sunday.
I will need to extend the stop that is on the short side but otherwise i am very happy with this tool. It is very good to have an excuse to use it!“We often contradict an opinion for no other reason
than that we do not like the tone in which it is expressed.”
Friedrich Nietzsche
-
2nd September 2012 12:12 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd September 2012, 01:26 PM #2Banned
- Join Date
- Feb 2012
- Location
- Adelaide
- Age
- 73
- Posts
- 153
Cold saws
When I was working as a welder, many, many, many years ago we used a cold saw with coolant pump. Although very quiet, accurate and clean, I always thought it very, very slow, blades were hellishly expensive and broke frequently (usually by the young kids), although, we did send a few out to be welded, much cheaper option. The question is, are they faster now and are blades cheaper and less prone to breakage?
-
2nd September 2012, 08:59 PM #3
Definitely, always wear safety glasses with a cold saw, swarf can bounce around and become a hazard and there is always a chance of a cut part dropping when you release the vise and splashing coolant toward your face. I prefer a fully enclosing google set like the the Uvex 9302 which will go over a set of specs if you need them. Can be found cheaper on ebay, but a very good set.
-
2nd September 2012, 10:29 PM #4
Cutting steel will never be fast until we get to have laser cutters at reasonable prices I suppose.
I can only compare with a mechanical hacksaw and the cold saw wins hands down, twice as fast and a quarter of the size. Compared with an abrasion cutter, well I hate them full stop so I don't compare. The new band saw are an interesting contraption but far too large for my workshop. I have seen both in action at Elcon steel and there seems to be little difference in speed.
I can certainly see how a blade can be broken or lose its edge. At $150 they are not cheap but neither are good quality tungsten tipped wood saw. Plus cold saw blades can be repaired and can be sharpened.
I have started on some work and all of a sudden cutting 6mm brackets into shape is a kids job. Love it all the way.
PS
I agree on the goggles.“We often contradict an opinion for no other reason
than that we do not like the tone in which it is expressed.”
Friedrich Nietzsche
-
3rd September 2012, 01:04 AM #5I break stuff...
- Join Date
- Aug 2010
- Location
- Melbourne
- Posts
- 539
If you're using the wrong blade (tooth count and profile) for the material, they do indeed seem to cut very slowly, and are more likely to break. I used to cut 1.75 inch exhaust pipe on mine with a 160 tooth blade (only one I had), and although it did it reasonably well, the blade seemed to chatter a lot in the cut. Then I picked up a pair of 220 tooth blades cheap, and the difference is night and day - much smoother in the cut, and twice as fast because the blade isn't bouncing...
-
3rd September 2012, 09:38 AM #6SENIOR MEMBER
- Join Date
- Aug 2012
- Location
- Australia
- Posts
- 521
The one thing I have found disappointing with the smaller cold saws is that they only come in single speed. They are usually geared for cutting mild steel. Most of the work that I do is in mild steel, but the flexibility to cut a piece of stainless from time to time is really a necessity for me if I am spending 1k+ and taking up the space in the garage.
-
3rd September 2012, 08:15 PM #7
A two speed cold saw 22rpm/44rpm comes with a 315mm diameter blade and about $500 to $800 more depending if you want the stand or not. You will also need a different blade.
“We often contradict an opinion for no other reason
than that we do not like the tone in which it is expressed.”
Friedrich Nietzsche
-
3rd September 2012, 09:07 PM #8I break stuff...
- Join Date
- Aug 2010
- Location
- Melbourne
- Posts
- 539
For what it's worth, I've cut 40mm solid stainless (unknown grade) on my single speed saw without any great difficulty. A little slow, but that's about it. If you were to cut stainless exhaust tubing, as I suspect you want to, I don't think there would be much issue...
-
3rd September 2012, 09:27 PM #9SENIOR MEMBER
- Join Date
- Aug 2012
- Location
- Australia
- Posts
- 521
Similar Threads
-
Cold Saw Options: Triton, Cold Saw, Power Hacksaw
By Jarh73 in forum METALWORK FORUMReplies: 41Last Post: 2nd May 2012, 09:15 PM -
You know its cold when.....
By DavidG in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 20Last Post: 26th June 2008, 11:32 AM -
How cold
By munruben in forum Woodies Quiz ForumReplies: 9Last Post: 22nd March 2008, 04:12 PM -
To cold to get up
By Phil Spencer in forum ROGUES GALLERYReplies: 9Last Post: 16th November 2006, 06:23 AM