Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: rust
-
29th October 2008, 05:10 PM #1
rust
GdatAll: need some help and advise,I have some freckles of rust appearing and adown drainpipe. It is acolor bondrectangle and I painted over the CB some time ago when I did the whole house. I purchasedwattylkillrustand read that it is for steel wrought ironandother ferrous metals,I called there service number and was told it was only good for the above.Checked with the hardware store and they say they sell it to plumbers etc and no one has complained or remarked .Has anyone hadexperiencewith this KR oncolor bonddowndraingor for that matter on any tin or aluminium products???I thought rust was rust and this is suppose to convert rust to ausefulmetallicsurface Anyhelp will be greatlyappreciatedand thanks in advance.billym
-
29th October 2008 05:10 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
29th October 2008, 05:19 PM #2Senior Member
- Join Date
- Apr 2008
- Location
- NSW
- Posts
- 356
Once rust starts on the inside of a metal downpipe it is very hard to stop it.
Expensive paints can cost as much as a new downpipe.
I would replace the downpipe with plastic and then paint it with wattle solar guard .
I have replaced all downpipes on my old house with cheap round stormwater pipe and fittings . Then painted with solar guard . They are still fine after 12 years near the ocean and I have just repainted house with solar guard.
-
30th October 2008, 07:39 AM #3
rust
Gday retromilling, thanks for you help, I guess the rust is all the way through, have to way of checking inside. Guess will have to replace same. they are over twenty years old and I am right on the coast. Funny that it is only two pipes both on the south side and one is facing the ocean and the other is at the back of the house.Many thanks for you advise.billym
-
5th November 2008, 07:51 PM #4Senior Member
- Join Date
- Apr 2008
- Location
- NSW
- Posts
- 356
My pleasure mate. I went for a trip last year down to Eden and back .
I must say that I like the south coast a real lot.
It reminds me of the Australia of my youth and a quiter and nicer time.
-
6th November 2008, 07:18 AM #5
rust
Gday retromilling: yes it is lovely but down this way. but unfortunately it is being found,Right up to Batesman bay seems to be bought out. Few years ago when Heinz tune factory closed you could have bought half the town for a hundred bucks but now back on top .Eden is a lovely spot.Only four or five fishing boats moored on the wharf now, used to be 25/30 tied up side by side and looked great.with lots of national parks around here it may remain green and not to crowded,guess it will depend on planning minister,lets hope with Sator gone sanity will prevail.G Luck billm
Similar Threads
-
Soluble oil and rust
By Bodgy in forum METALWORK FORUMReplies: 25Last Post: 10th June 2008, 07:02 PM -
Rust
By m2c1Iw in forum HAND TOOLS - UNPOWEREDReplies: 16Last Post: 22nd May 2007, 09:51 AM -
Rust removal
By Wolfs in forum WOODWORK - GENERALReplies: 17Last Post: 24th February 2006, 11:45 PM -
Rust Prevention
By Dean in forum WOODWORK - GENERALReplies: 19Last Post: 27th November 2002, 09:07 PM