Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 46 to 60 of 60
Thread: Large scraping straight edge
-
9th May 2014, 11:18 PM #46Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
-
9th May 2014 11:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th May 2014, 11:38 PM #47SENIOR MEMBER
- Join Date
- Jul 2011
- Location
- Melbourne Australia
- Posts
- 1,128
I was so bored I managed to spray paint it Dulux Blue. You owe me a new pallet BTW. This one seems to be covered in blue paint. It used to say Chep, now it just says "ep" I did you a favour, those shinny bit's looked like they might rust. I gave those a real good squirt. Sorry about the runs, but they should buff right out. You should be able to cut and polish that, and it will come up looking better than my F100. Yeehar
-
10th May 2014, 04:23 PM #48
Yee Hah... that should be right at home in the badlands of Rocky..
That price is cheap cheap cheap... New price these days is in the thousands.. and of course being older it will be more stable.... (cough!).. The cast iron will have stabilized, unless you paint it Dulux Blue, then all bets are off..
Ray
-
10th May 2014, 05:16 PM #49GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Hi Phil
Make sure to stamp his name in on it with a center punch so no one it tempted to knock it of......pick somewhere nice and flat so it really stands out.
Stuart
-
10th May 2014, 06:37 PM #50Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
You are all a mob of bastards....
.
.
.
.
.
.
.
.
.
.
Light red, the colour of choice for the discerning man.
-
10th May 2014, 07:02 PM #51Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Don't worry about it Richard. My surface grinder is almost complete so when it is I can put it on the table and grind the punch marks out. It's got a traverse of 10", so that should be more than enough to grind out the marks, even if they are deep.
Michael
-
10th May 2014, 08:02 PM #52
-
13th May 2014, 12:50 PM #53GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
so mine may be worth a lot more than the $275.00 as quoted above
https://www.woodworkforums.com/showth...ght=camel+back
-
15th May 2014, 06:48 PM #54Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Thanks to stix012 here is the 5 footer he found for me.... It only has a milled finish on the base, but on the surface plate is only about 0.03mm high in the middle...
20140515_170826.jpg
Just waiting for Ray to deliver the 4 footer now.... I think if I say he will do it enough times, he will do it in the endLight red, the colour of choice for the discerning man.
-
26th March 2015, 06:41 PM #55Senior Member
- Join Date
- May 2011
- Location
- Castlemaine
- Posts
- 144
-
26th March 2015, 07:50 PM #56future machinist
- Join Date
- Mar 2008
- Location
- nowra
- Posts
- 1,361
-
26th March 2015, 11:43 PM #571915 17"x50" LeBlond heavy duty Lathe, 24" Queen city shaper, 1970's G Vernier FV.3.TO Universal Mill, 1958 Blohm HFS 6 surface grinder, 1942 Rivett 715 Lathe, 14"x40" Antrac Lathe, Startrite H225 Bandsaw, 1949 Hercus Camelback Drill press, 1947 Holbrook C10 Lathe.
-
27th March 2015, 09:20 AM #58Senior Member
- Join Date
- May 2011
- Location
- Castlemaine
- Posts
- 144
Face Plate Trade
Hi Ew and Andre,
As I do not have a face plate for the DSG my preferred option is to swap/trade the D1-4 face plate for a D1-6 face plate.
Do ether of you guys have a "spare" D1-6 face plate?
Cheers
Piers
-
27th March 2015, 06:09 PM #59
Sorry Piers,
I only have the 14" D1-6 faceplate from the Antrac, and i need it. No where to look for one around here either. Gone Dre may be able to check Mick Moyles.1915 17"x50" LeBlond heavy duty Lathe, 24" Queen city shaper, 1970's G Vernier FV.3.TO Universal Mill, 1958 Blohm HFS 6 surface grinder, 1942 Rivett 715 Lathe, 14"x40" Antrac Lathe, Startrite H225 Bandsaw, 1949 Hercus Camelback Drill press, 1947 Holbrook C10 Lathe.
-
27th March 2015, 06:14 PM #60future machinist
- Join Date
- Mar 2008
- Location
- nowra
- Posts
- 1,361
HAHah Nice Ewan I can I have a look at my sources. I may buy one from the usa not sure on their weight though
BETTER TO HAVE TOOLS YOU DON'T NEED THAN TO NEED TOOLS YOU DON'T HAVE
Andre
Similar Threads
-
How straight does a straight edge need to be?
By Sir Stinkalot in forum WOODWORK - GENERALReplies: 20Last Post: 8th November 2013, 10:41 AM -
What preceded the edge-to-edge joint for creating large surfaces?
By Russell Cook in forum WOODWORK - GENERALReplies: 15Last Post: 25th November 2012, 04:22 AM -
Aluminium straight edge - not so straight
By Dengue in forum WOODWORK - GENERALReplies: 28Last Post: 7th November 2010, 09:54 AM -
3-edge roundover, 1-edge straight.
By CT in forum ROUTING FORUMReplies: 8Last Post: 21st May 2006, 01:05 AM -
3m straight edge - or how straight can one get angle iron
By burn in forum WOODWORK - GENERALReplies: 10Last Post: 16th February 2004, 07:06 AM