Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 30 of 405
Thread: The new scraping thread
-
1st June 2011, 10:48 PM #16Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Not as bad as what you think... Around $2300 for a 36X24 Starrett.... There is a dealer in Sydney that sells them..
I have similar tools to Greg... An old 7EL Biax and I also use Canode ink, but I also have some home brew Prussian Brew given to me by a professional tool rebuilder in Melbourne.. It is just prussian blue powder and grease mixed together..
I also have some Yellow canode for highlighting...
Currently working on a Macson TC grinder... Very slowly... It only has one set of V and flat to scrape.. I have got the flat done but need to make up a template for the V.. I purchased some cast iron bar today to make the template.. Like Greg I also have a 18 and 38" straight edge that we purchased as cast from the US..
-
1st June 2011 10:48 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
1st June 2011, 10:53 PM #17Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
-
1st June 2011, 11:28 PM #18Dave J Guest
RC,
I thought you had the Biax flaker as well that you used on you vice?
Dave
-
1st June 2011, 11:33 PM #19Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
No, I did a bit of hand flaking on it.... What a disaster that was (the flaking)
BTW I am selling my 18"X24"X3" surface plate if anyone is interested... $165+ freight..ex Rockhampton Qld..
-
1st June 2011, 11:42 PM #20GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Got some more details on the plate .RC.? sounds like something I would be interested in. I'll pm you
Stuart
-
2nd June 2011, 12:13 AM #21GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
.RC.
Did you use the horizontal head because it made the work holding easier?(What do you think of that head btw, should I be looking out for one?)
What angle did you put on the side face of the smaller one?
Stuart
-
2nd June 2011, 12:14 AM #22
Hi Stuart,
I can provide storage for you (at a competitive rate) if you can't find room for it.
Regards
Ray
-
2nd June 2011, 12:45 AM #23GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Well thanks Ray, but I think you have enough pretties already, I need to lift the tone of my shed lol. If you have a job in mind i'm sure we can work something out. Thats assuming it ends up in my shed.
Stuart
-
2nd June 2011, 01:23 AM #24Dave J Guest
Hi Stuart,
You are lucky it's still there. RC posted up about it on PM a few months ago, and I thought it would have gone by now.
Dave
-
2nd June 2011, 08:37 AM #25GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
-
2nd June 2011, 03:21 PM #26Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Found this in Melbourne
http://www.toolingonline.com.au/home...category_id=63
-
2nd June 2011, 05:56 PM #27Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 58
- Posts
- 2,557
-
2nd June 2011, 07:18 PM #28
Thanks for the link RC. I sent a message regarding larger sizes (I imagine I'm not Robinson Crusoe there?)
GregIt's all part of the service here at The House of Pain™
-
2nd June 2011, 07:24 PM #29GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
What is a "Smooth 'Ball bearing' surface"?
Bryan,
Did you get in before their price rise?
Stuart
-
2nd June 2011, 07:38 PM #30Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Similar Threads
-
More on shear scraping
By Tiger in forum WOODTURNING - GENERALReplies: 20Last Post: 12th June 2010, 12:55 PM -
Scraping epoxy
By Arron in forum BOAT BUILDING / REPAIRINGReplies: 21Last Post: 12th June 2009, 10:37 PM -
Scraping
By wheelie in forum WOODTURNING - GENERALReplies: 8Last Post: 23rd September 2006, 09:40 AM -
scraping / tear out
By gnu52 in forum WOODWORK - GENERALReplies: 4Last Post: 19th June 2006, 06:53 PM -
Scraping
By 9Fingers in forum WOODWORK - GENERALReplies: 22Last Post: 28th January 2006, 04:32 AM