Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
-
9th February 2015, 03:57 PM #1.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Spindle Seals and Heat Generation
Yesterday I needed to drill a some holes in a pair of grinding wheel nuts and I chose to use my dainty imperial Hercus mill for the task. ( The other mill, little but not dainty, is metric and this was an inch job.) Then I remembered why it has sat forlornly under a sheet for four or so years now. After a few minutes of running, the spindle in the mill's vertical head had become nearly too hot to touch. I had mentioned this in the Hercus forum a few years back and Bruce "Abratool" informed me that his mill's head ran cool. It ran cool because it had no seals. With no seals mine too runs cool. No seals would necessitate the wearing of a plastic raincoat or in Bruce's case, a wetsuit.
The original seals are single lipped, steel cored with a garter spring. With the springs removed the heat persists. Hercus used Flaseal 13297 seals. I replaced the originals with NAK seals. They measure 2.500" x 1.875" x 0.375". This morning I had a look for PTFE seals but without success.
I imagine Hercus used lipped seals on the head to retain the oil more than to exclude dust and swarf. The No.1 T and C grinder utilises labyrinth seals to do both but the spindle is horizontal.
Can anyone suggest an alternative to the lipped seal?
Bob.
-
9th February 2015 03:57 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th February 2015, 04:14 PM #2Intermediate Member
- Join Date
- Jan 2012
- Location
- Melbourne
- Posts
- 44
DIY labyrinth? Minimise the clearances, you should be fine.
Neil
-
9th February 2015, 04:42 PM #3SENIOR MEMBER
- Join Date
- Jul 2011
- Location
- Melbourne Australia
- Posts
- 1,128
G'day Bob.
A Vee-ring might get you out of trouble. Because you can alter the axial position of the seal, you can play with seal contact pressure. The also have the joy of opening up when they are spinning, becoming more of a flinger than a contact seal.
They are nominally metric, but fit a wide tolerance range, so you can run them on Imperial shafts.
http://www.allsealsinc.com/pdfs/skfvringcatalog.pdf
Take a look at the VR1 style - #400450.You would squeeze that in there, and have it running on the seat of the original seal housing, or rework that front cover.
I retrofit these into some spindles. Those that run on CNC plasma cutters, that carry a spindle for drilling all so.
They work best against a hardened, fine surface finish face. I have them Ceramic HVOF sprayed, then ground and lapped. You wont need that at the speeds of a Hercus.
Regards Phil.
-
9th February 2015, 05:34 PM #4.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Hi Phil,
I did contact SKF when you suggested the possible use of their Vee Ring as an alternative to the revised additionally sealed Timken taper bearings in the T and C workhead. In the case of workhead there wasn't sufficient clearance available in which to shoehorn a seal. Sadly that remains an unresolved problem.
The vertical head is blessed with more space. Maybe a seal will fit without too much fooling around. I will have a close look at the seal you recommend.
Thank you.
Bob.
-
9th February 2015, 07:26 PM #5Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
-
9th February 2015, 08:12 PM #6Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 920
Wave oil seals claim to run cooler than the usual type garter seal with a straight lip, as well as some other benefits.
Sealed bearings (when available) touch the metal surface very lightly, compared to garter seals.
Jordan
-
9th February 2015, 08:24 PM #7SENIOR MEMBER
- Join Date
- Jul 2011
- Location
- Melbourne Australia
- Posts
- 1,128
SKF were sort of late to that party. I think they bought into some one, to get those seals on the books.
NAK do them, any of the other bearing companies should be able to get them.
http://nak.com.au/technical/NAK_VSealsInstallGuide.pdf
I'd probably have one sitting in my bearing cabinets, if you wanted one sent over to play with.
Regards Phil.
-
10th February 2015, 12:19 AM #8.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Not always lightly enough Jordan. Another project requiring attention - https://www.woodworkforums.com/showth...12#post1788512
If it is not too much of a pain in the neck I'd love to have a play Phil.
-
10th February 2015, 12:24 AM #9.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Michael,
There is next to no heat if the seals are absent.
Not always lightly enough Jordan. Another project requiring attention - https://www.woodworkforums.com/showth...12#post1788512
If it is not too much of a pain in the neck I'd love to have a play Phil.
-
10th February 2015, 06:42 AM #10Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Similar Threads
-
Shop made vacuum bag seals - anyone?
By Dengue in forum WOODWORK - GENERALReplies: 6Last Post: 20th November 2014, 10:44 AM -
PVC Ducting Joint Seals
By ronboult in forum DUST EXTRACTIONReplies: 3Last Post: 27th March 2014, 04:28 PM -
Generation Y
By Barry_White in forum WOODIES JOKESReplies: 1Last Post: 4th January 2009, 03:00 PM -
Stolen Generation
By Rossluck in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 32Last Post: 14th July 2007, 08:12 PM