Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 22 of 22
Thread: steady rest fun
-
22nd December 2011, 09:38 AM #16GOLD MEMBER
- Join Date
- Mar 2011
- Location
- Dural NSW
- Age
- 82
- Posts
- 1,120
Acme Screw
Mike
Well done, the finish on the screw looks very good.
Just like a bought one
Think of the pleasure in making it
regards
Bruce
-
22nd December 2011 09:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
22nd December 2011, 11:39 AM #17SENIOR MEMBER
- Join Date
- Apr 2008
- Location
- Canberra
- Posts
- 816
Nice Job. I am going to play with my my steadies soon. What RPM were you using for this job? How often did you have to lube the steadies?
Brendan
-
22nd December 2011, 11:42 AM #18
acme
Thanks .... Having done one, at least I know I can make more ACME cross feed screws if the need arises . Next thing is, making the bronze ACME nuts to suit the screws I must buy some of the proper 12l14 steel, instead of using unknown grade stuff salvaged from old printers MIKE
-
22nd December 2011, 11:49 AM #19
speed
Brendan, I was using 60 rpm . I lubed both the screw and the steady often ( I used neatsfoot oil on the thread ) as I was cutting it . One thing I found out , is that the fingers on the steady need to be centred on the shaft accurately , otherwise problems will arise . The 8 tpi ACME cutters I bought on EBAY , not sure but I think they are carbide , they do work OK despite the low rpm. MIKE
-
22nd December 2011, 11:56 AM #20Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 58
- Posts
- 2,557
I tried an acme nut once. Used ali for practice. Bit more forgiving. It sure focuses the mind into a small space. Have fun.
-
22nd December 2011, 02:53 PM #21SENIOR MEMBER
- Join Date
- Apr 2008
- Location
- Canberra
- Posts
- 816
Thanks Mike.
I did wonder if the carbide would cut well at those RPMs...my carbide threading inserts arent real flash at subsonic speeds. Obviously yours worked well though as the finished result looks good.
How do you center the fingers accurately?
Brendan
-
22nd December 2011, 03:28 PM #22
finish
Brendan , yes I was surprised at the finish I got too . With the steady fingers > If you draw a line from the centre of the fingers ..you want that line to intersect the centre of your work piece shaft . ... Hope that explains it . I have just taught myself from trial and error
Similar Threads
-
Steady Rest
By Paul39 in forum WOODTURNING - GENERALReplies: 25Last Post: 24th July 2011, 03:04 PM -
A Steady Rest for the Hercus 260
By cba_melbourne in forum THE HERCUS AREAReplies: 1Last Post: 25th May 2011, 01:39 AM -
Best kind of steady rest
By Tiger in forum WOODTURNING - GENERALReplies: 8Last Post: 8th July 2010, 05:54 AM -
Steady Rest & Vase/weedpot ????
By yaryetnom in forum WOODTURNING - GENERALReplies: 5Last Post: 19th July 2009, 07:03 AM -
Four-Wheel Steady Rest
By joe greiner in forum WOODTURNING - GENERALReplies: 21Last Post: 30th November 2008, 05:21 PM