Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 24 of 24
Thread: Threading Charts?
-
4th June 2014, 08:29 AM #16Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
Metric is easy to work out.
Thread OD in mm - pitch in mm = drill tap size.
eg. 10mm X 1.5mm thread
10 - 1.5 = 8.5mm tapping hole sizeLight red, the colour of choice for the discerning man.
-
4th June 2014 08:29 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th June 2014, 11:31 AM #17
Thanks again for this thread. I have installed a PDF viewer on my tablet and can have this information in my pocket.
Dean
-
6th June 2014, 07:31 PM #18
Groovers, I have sent an email of to Suttons and just waiting to see what they say. Damien.
I'm a dancing fool! The beat goes on and I'm so wrong!!!!
-
6th June 2014, 07:39 PM #19
Thread nomenclature.
Groovers, I am trying to fabricate some bits and pieces to modify/enhance some hand tools. The pieces require 2 metal rods and at the end of them there is a thread that is a tad confusing.
This is what came with the drawing 8-32-2A-Rh. What does it mean? Damien.I'm a dancing fool! The beat goes on and I'm so wrong!!!!
-
6th June 2014, 07:49 PM #20Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
I think it is a US designation -
#8x32tpi
2A(the grade)
RH (RH thread)
A #8 is 0.164" major diameter - a smidge over 4mm
Michael
-
6th June 2014, 07:51 PM #21Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
8-32 is the thread size or #8 UNC
2A the thread tolerance
rh = right handLight red, the colour of choice for the discerning man.
-
6th June 2014, 08:06 PM #22
Thanks people. All I need is time. Thanks again. Damien.
I'm a dancing fool! The beat goes on and I'm so wrong!!!!
-
6th June 2014, 08:44 PM #23
I got one of these as a wall chart http://www.goliath.com.au/Technical%20Information.htm you can download an A2 pdf, but then you have to print and laminate it.
Ray
-
6th June 2014, 09:41 PM #24
Damien,
Ok you are now up to speed on what those tap specs signify - so from there a tapping drill size should be selected.
My Sutton card says a 3.4mm ( this dimension may vary slightly from chart to chart ) drill for 8-32. That size drill bit is unlikely to be kept at a school (state school at least). You may need to see your local engineers supplier for it.Easier still use the 3.5mm in the standard drill index .its only a tiny bit o size, but hey! I am a rough as guts boilermaker. If the thread is loose , put on a dab of Fitter in Bottle - Loctite.
None of us have any idea of your engineering knowledge - the extent of your experience in drilling and tapping -and that may have a reflection on whether or not your job could fail or succeed. A bit more information will be good if you need more help.
Do you require information on how to hold the work, on keeping the tap centered, the drill machine rpm for the drill bit?
The extensions that you propose, are they parallel to the tool shank axis or are they perpendicular to its surface 90 degrees to the axis? If so, how do you propose to hold and drill and tap the tool shank.?
Dependent on which result that you desire, there may be varying methods of achieving the outcome.
I have one Sutton thread card I found in a drawer today ,while looking for something else. PM me your snail mail address and I'll drop it in an envelope for you if you want it.
cheers
Grahame
Similar Threads
-
Unit Conversion Charts/References - Lumber Sizes etc.
By soulspirit in forum WOODWORK - GENERALReplies: 13Last Post: 16th October 2022, 11:29 PM -
My new threading Jig
By dai sensei in forum WOODTURNING - GENERALReplies: 16Last Post: 7th June 2012, 09:00 AM -
Threading again
By morrisman in forum METALWORK FORUMReplies: 18Last Post: 10th December 2011, 03:16 PM -
Abrasive & Sharpening Conversion Charts
By FenceFurniture in forum FINISHINGReplies: 1Last Post: 12th February 2011, 11:34 AM -
Timber Charts??
By Bruce101 in forum TIMBERReplies: 6Last Post: 7th March 2007, 04:55 PM