Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 22 of 22
Thread: tool to remove a 'fitting'
-
8th September 2013, 09:16 AM #16Senior Member
- Join Date
- Nov 2008
- Location
- Qld. Australia
- Posts
- 417
17mm tube spanner shimmed on two flats.
Nev.
-
8th September 2013 09:16 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th September 2013, 12:52 PM #17GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
Others who have described the procedure on the net do not seem to have needed any special tools, one stated that he just used an open end spanner. Cutting a socket might mean the socket walls will expand due to lack of support, an impact socket would be better if it will fit as the walls are far thicker.
CHRIS
-
8th September 2013, 08:20 PM #18SENIOR MEMBER
- Join Date
- Sep 2006
- Location
- Australind ,WA
- Age
- 58
- Posts
- 849
I can't see how you could use an open ended spanner, as I tried that first. There is simply not enough room to gain enough purchase to undo it. I got about 1/8 of a turn and that's it....
Maybe others found the fitting came loose after it moved that much. The one I did get undone ( it took some damage doing it ) took a full turn before it could be turned by fingers alone.
I agree, cutting a socket might allow it to expand unless I cut just enough out to get purchase.......
An impact socket may not fit due to the wall thickness....
I made some 1mm shims today and bought another 17 mm socket, so will try it tomorrow.
Steve
-
8th September 2013, 10:01 PM #19GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
If it were me, I would simply shape a suitable piece of 10 or 12mm flat bar into a spanner, drill a 17mm hole and then build up two flats with a welder in the appropriate places and finish them with either a file or a die grinder. If you can't use a spanner type piece due to space then weld a this piece as described onto the end of a socket. Job done. You could even use a suitable open end spanner, ground to achieve clearances with the end closed in for strength.
-
9th September 2013, 08:30 PM #20SENIOR MEMBER
- Join Date
- Sep 2006
- Location
- Australind ,WA
- Age
- 58
- Posts
- 849
All done.....
I've done this job and the tool worked well.
I glued ( so I didn't damage the socket with heat and because it was quick. ) in two 1 mm shims inside a 17 mm socket.
Very snug fit and it needed to be. One of the fittings was very tight.
Steve
WP_20130909_003 (Medium).jpg
-
9th September 2013, 08:38 PM #21SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
Well done Steve.
A tricky one solved relatively easily
Phil
-
9th September 2013, 09:03 PM #22GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
Good job.
Similar Threads
-
New member looking for appropriate tool/fitting
By fearlessflier in forum METALWORK FORUMReplies: 30Last Post: 17th December 2011, 06:52 AM -
ho to remove tru-oil
By old_picker in forum FINISHINGReplies: 6Last Post: 24th August 2010, 09:25 AM -
Fitting VM jaws to T/tool chucks
By rsser in forum WOODTURNING - GENERALReplies: 22Last Post: 12th October 2008, 10:10 AM -
Anyone know about a Tool or machine to remove old roofing nails??
By WoodyKnot in forum HAND TOOLS - POWEREDReplies: 9Last Post: 20th November 2006, 11:03 AM -
How do you remove a splinter?
By echnidna in forum WOODWORK - GENERALReplies: 36Last Post: 26th May 2005, 02:33 PM