Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Trouble with calibrating level
-
13th August 2012, 08:02 PM #1Novice
- Join Date
- Mar 2012
- Location
- Toowoomba Qld
- Posts
- 11
Trouble with calibrating level
Well, finally after many months of deliberation, finally have a new lathe (al-960 with dro). Got it set up today and cleaned down. Recently purchased a measure max precision level, went to test it out to level lathe up but took me 4 hours to get it to read the same when you turn it 180degrees. Don't know if anybody else has had this problem as I have read through all the old threads on lathe leveling Hopefully it will stay the same overnight, am following Dave J's method..
-
13th August 2012 08:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th August 2012, 08:09 PM #2
The sensitivity of a master precision level requires a very well made adjustment screw, patience, and a careful approach to controlling temperature growth of any part of the level or the surface. It cqn be seriously vexing, but it shouldn't take four hours.
Have you kept handling the lefel to a minimum during the process? I wear ski gloves when handling levels and spotting masters as ai gre tired of chasing my tail which is what happens with only a small warm spot on any of the apparatus.
GregIt's all part of the service here at The House of Pain™
-
13th August 2012, 09:59 PM #3GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Hi Mark,
What are you sitting the level on when you are checking it?
As the base is very likely not flat(mine wasn't), its placement needs to be very repeatable. Its going to make life hard but you can get there.
As Greg says, even with everything going for you its only tiny movements.
The lathe doesnt need to be level just the same both ends, so as long as you dont turn the level 180 when you change ends, you should be set.
Stuart
-
13th August 2012, 10:24 PM #4Dave J Guest
Hi Mark,
It sounds like you have it pretty sorted now, but you can start with a carpenters lever to get it close, then switch levels.
Like Stuart said, try to use the same place on the level each end, I even mark my level and parallels with a texta so I know it's going in the same spot each end.
One thing to watch out for is if the bubble is touching either end, it will have you chasing your tail for hours.
Dave
-
14th August 2012, 11:14 AM #5Novice
- Join Date
- Mar 2012
- Location
- Toowoomba Qld
- Posts
- 11
Thanks for the advise guys. Hopefully have it sorted now. Am using ground parallels and marking them with texta to get it in the same position each time I move it. Was a very tedious job but should be well worth it in the long run. As they say "Patience is a virtue"
Thanks again
Mark
-
14th August 2012, 06:19 PM #6Senior Member
- Join Date
- Jun 2012
- Location
- Germany, Outback of Munich
- Posts
- 213
Am using ground parallels and marking them with texta to get it in the same position each time I move it.
If you work lengthwise, put it on the saddle and leave it there. Crank the saddle over the full length.
Do the same for the X-axis.
As soon as you move it, you just have a new zero-point and proceed along one axis (X or Z).
It also isn't important (in the case of a lathe) that the level gives the same reading when you rotate it by 180°.
Even better if you do have two levels!
Nick
-
15th August 2012, 09:36 AM #7GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
-
15th August 2012, 11:15 AM #8GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Hi eskimo,
I think Nick means using two levels on the saddle at 90degs to each other, one for X and one for Z. Then you dont have to keep moving them, saving you the trouble of getting repeatablity and rechecking of zeros each time.
Stuart
-
15th August 2012, 03:21 PM #9GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
ah ah that makes sense
-
15th August 2012, 08:13 PM #10SENIOR MEMBER
- Join Date
- Sep 2006
- Location
- Mallacoota,VIC,Australia
- Age
- 53
- Posts
- 656
HI,
I am a bit Late here, but I had the same Trouble with My Machinist Level that I Bought of Shars. The Temperature seemed to be Inconsistent in the Shed and I couldn't get the level to Work Properly. I had checked the level the Night before in the House on a Granite Surface Plate and the Calibration was O.K. .
I ended up using an Electronic Level that I Bought of VEK Tools to level My AL-960b Lathe. When I Read Greg Q Comments My problems might have been My Own - touching the level to Much. I will try with Gloves next Time.All The Best steran50 Stewart
The shortest way to do many things is to do only one thing at once.
Similar Threads
-
Calibrating a tri-sqaure
By RedShirtGuy in forum WOODWORK - GENERALReplies: 15Last Post: 29th April 2012, 10:37 PM -
Stanley Rule and Level Co no93 Spirit Level
By Sapling in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 24th May 2010, 07:23 PM -
Calibrating my domino
By Wongo in forum FESTOOL FORUMReplies: 11Last Post: 1st September 2008, 12:06 AM -
calibrating a c.i. tablesaw
By jow104 in forum WOODWORK - GENERALReplies: 8Last Post: 18th August 2005, 09:41 AM -
Calibrating precision mortising jig
By Rocker in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 0Last Post: 5th February 2004, 04:41 PM