Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 25
Thread: Waldown Drill Press
-
26th August 2011, 12:41 AM #1
Waldown Drill Press
There are a couple of Waldown Workmax Mark I's for sale by tender.
This 3 phase model:
and this single phase unit:
Any thoughts on what they may be worth?Kev
-
26th August 2011 12:41 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
26th August 2011, 10:51 AM #2.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Hello Kev,
I paid 200 dollars for my 3M and I think 175 for a little single phase drill, the same as the one shown in your photo. The latter came with a genuine Waldown vise. Shamefully, the vise looked like a colander.
The first photo below was taken about four years ago.
Bob.
-
26th August 2011, 08:43 PM #3
Here is a rare one: WALDOWN THREE HEAD DRILL PRESS | eBay
-
27th August 2011, 06:36 PM #4
Thanks Bob.
That gives me some guidance.Kev
-
27th August 2011, 06:39 PM #5Dave J Guest
That first on looks happy.
Dave
-
28th August 2011, 05:30 PM #6SENIOR MEMBER
- Join Date
- Jun 2011
- Location
- Australia east coast
- Age
- 71
- Posts
- 1,469
-
29th August 2011, 05:08 PM #7
-
29th August 2011, 07:43 PM #8SENIOR MEMBER
- Join Date
- Jun 2011
- Location
- Australia east coast
- Age
- 71
- Posts
- 1,469
Far be it for me to defend the quality of the Chinese drill presses - I have a lot of issues with mine, but it does drill holes.
However those Waldowns don't have rack & pinion table height adjustment, they have less speeds and if they're the same as my Richardson, changing the belt involves a lot of work if it ever goes bad! Either pulling the spindle or prising out the top locating bushing (which goes round & round but refuses to come up & out, not sure if it does come out). A link belt is the obvious answer, if you want to spend approx $100 for 1.2m of the stuff.
Also, changing speeds is fiddly, no quick release tension adjustment and only 6 speeds. I think the price I paid for it was about right, I certainly wouldn't pay more than $200 maximum for one. More like half of that
If you want a quality drill, keep your eye out for an Arboga geared head model. However it's going to cost.
PDW
-
29th August 2011, 09:40 PM #9.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Belt changing could not be simpler on the Waldown. If you want to read about the trials and tribulations of one bloke's Arboga ownership have a look here - https://www.woodworkforums.com/f65/ar...-drill-131401/
Granted, it's a mill/ drill but some of the issues Ken has faced would also apply to the drill. I looked longingly at an Arboga drill a couple of months ago and I would have one if I had three phase power.
BT
-
29th August 2011, 10:56 PM #10SENIOR MEMBER
- Join Date
- Jun 2011
- Location
- Australia east coast
- Age
- 71
- Posts
- 1,469
OK those Waldowns are nothing like my Richardson in either belt changing or changing the belt from one pulley to another. Much simpler & better design. Funny because visually the castings are similar.
As for Arbogas, there's always a risk in buying used equipment. I've had one of the baby Arboga radial arm drills for 15 years. It's beat up, rattly, noisy and extremely well used. Still drills holes up to 35mm dia without dramas. That's the biggest drill bit I own.
PDW
-
30th August 2011, 12:45 AM #11.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
PDW,
I posted some photos of a little radial arm drill a while back. It was a work of art.
https://www.woodworkforums.com/f65/arboga-131333/
BT
-
30th August 2011, 11:37 AM #12.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
This drill has nearly 11 hours to go on Ebay and it's up to $351.99
And this one sold yesterday for $122.50. I wonder if Joe was the winning bidder?
-
30th August 2011, 10:12 PM #13
The first one went for $5,600.00, better increase the insurance on them Waldown drill presses
http://offer.ebay.com.au/ws/eBayISAP...m=160642465281
-
30th August 2011, 10:15 PM #14
-
30th August 2011, 10:16 PM #15Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 59
- Posts
- 2,557
Ok that's getting silly.
Similar Threads
-
Thoughts on Waldown BDB13 - CHEAP drill press...
By CameronPotter in forum GENERAL & SMALL MACHINERYReplies: 10Last Post: 22nd May 2010, 11:00 PM -
Waldown drill press
By mikm in forum GENERAL & SMALL MACHINERYReplies: 5Last Post: 17th August 2009, 10:35 AM -
new drill press: quill stroke vs drill bit length ?
By bannock in forum GENERAL & SMALL MACHINERYReplies: 2Last Post: 21st June 2008, 09:09 AM -
Waldown Drill Press Conversion
By lockwood116 in forum WOODWORK - GENERALReplies: 1Last Post: 3rd September 2006, 06:09 PM