Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 67
-
19th September 2011, 10:40 PM #1.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Another Waldown - this time a tart up.
Stuart has eclipsed all my show and tell stuff with his Kitten Kamera. So this is not the usual presentation but rather an attempt to document the reburbishment of an example of Waldown's most basic drill. I had offered this machine to Joe but with him now being the proud owner of a Servian drill, and no longer desiring the beater, I thought I would utilize the column and pedestal base to transform my other bench model Waldown into something more useful.
The column was brown with rust and featured the mandatory nicks and scratches that come with 40 years of use. The later are easily dealt with by simply rotating the column so they face the rear. The rust came off readily with some 120 wet and dry and kerosene followed by 240 and a Scotchbrite pad.
The tricky part of the refurbishment will be the table and the filling of the drill holes. My plan ( which could change ) is to cannibalise the ruined 3M table I have by cutting it up and turning plugs from the cast iron in an attempt to acheive uniform colour and hopefully invisible repairs. Bear in mind, Waldown want over 400 dollars for a replacement table.
I think I might still have enough paint left over from my 3M reclamation. The problem is that it is gloss spraying enamel. Satin would be my preference but I have had no luck with matting agents. My last attempt looked like I had mixed beach sand into the paint. I will need help from those better versed in these matters when the time comes.
BT
-
19th September 2011 10:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th September 2011, 11:09 PM #2Senior Member
- Join Date
- Jun 2011
- Location
- Adelaide
- Age
- 27
- Posts
- 249
Nice, that came out really nicely
Its a shame that they want $400 for the table :/
-
19th September 2011, 11:16 PM #3
Nice work already Bob!
I'll be watching with great interest as I pretty my Servian up. I'm yet to clean and try the motor. The switch is broken and doesn't move, so that will be the first two tasks. The I'll follow your example, OK?
BRW, the column on the Servian is SOLID - geez its heavy!
Joe
-
19th September 2011, 11:45 PM #4GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
I thought the column on my Servian was just capped, solid explains why it is so heavy. Mine is only 4 speeds but I have a tricky plan to put a VFD on it. Are all these drills made in Sweden?
CHRIS
-
19th September 2011, 11:58 PM #5Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 59
- Posts
- 2,557
Bob, I too will be watching with interest. You have high standards to meet (your own I mean). Bunnings mixed a Dulux semi gloss enamel to match my sample for my tailstock. It doesn't seem to brush well though; do you have a gun? BTW, I hope you're not giving me a better table than the one you're going to patch? Or are they different?
Joe, are you going to show us the Servian? In its own thread of course. The column on the Tough is solid too and it weighs a ton. I've only tackled it with scotchbrite so far, with limited success. Seeing Bob's results I will be a bit more abrasive with it.
-
20th September 2011, 12:00 AM #6GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Ok BT wins the prize for the best name. lol
Nice work so far, as always. Couldnt you soill something on the fall to make us feel better?
$400! I bet they have plenty in stock at that price lol
Stuart
-
20th September 2011, 12:52 AM #7.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
" Couldnt you soill something on the fall to make us feel better? "
I'm stumped Stu. Are you testing us with a bit of Latvian? Insprired by the sprat tin?
BT
-
20th September 2011, 01:06 AM #8.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Bryan,
The tables are both from the same model drill. Condition wise, the one I'm keeping might have a few less drill marks. Both have been gnawed around the centre hole. I'm thinking of cleaning the mess up with a boring head and making an insert to reclaim the lost cast iron. I like the centre hole. The 3M table does not have one and I have to be ever vigilant that I don't create one.
I sprayed the 3M.
Bob.
-
20th September 2011, 01:35 AM #9
OK, I will start a new thread on the Servian shortly - since you asked. I'll have to go and take some photos.
Mini, how do you know yours is made in Sweden? I haven't yet found any manufacturers evidence...
Bob et al, I have a question: my drill is missing the quill return spring. It looks like a standard flat strip coil spring in the left end of the pinion shaft inside a recess of the head casting. Any ideas where I might get a suitable spring for that?
Joe
-
20th September 2011, 08:31 AM #10.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
I was able to purchase a new spring for my Waldown 3M from Fiora Machinery, one of the distributors over here. Try the factory in Dandenong. If anyone can make something fit it will be you Joe.
A couple of small narrow nose vise grips come in handy when installing the spring. You hold the spring in it's wound up state with a wire loop and fit it into the recess.
Waldown have a slot in the end of the pinion to locate the inside end of the spring. Hopefully Servian used a similar set up.
BT
-
20th September 2011, 09:48 AM #11Originally Posted by BT
The column looks nice, I'm looking forward to seeing the rest as it progresses.
Hi Mini, Australian made I think, they are still around it seems.. I found a "Servian Machine Tools" on google. I'm guessing that's it's the same company.
I can vouch for the weight of Joe's solid column Servian, that thing weighs a ton...
Regards
Ray
-
20th September 2011, 12:07 PM #12GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
Mine has got a fairly large brass tag on it above the height handle saying made in Sweden and I just presumed they all were. It is a four speed gear head drill BTW. After I got it many years ago when I saw it standing unused in a workshop I made some inquiries and the company was in Belfield NSW. If memory serves me correctly I have in mind that the brand was a bit generic like the Taiwanese suppliers of today but I may be wrong there. I have seen one the same as mine but eight speed which would be nice.. My mate has it in a machine shop and he has promised to leave it to me in his will. BTW mine cost me $50 about 25 years ago.
CHRIS
-
20th September 2011, 02:51 PM #13Dave J Guest
Watching with interest Bob,
Dave
-
20th September 2011, 08:59 PM #14
Thanks Bob! This is exactly the same arrangement as on the Servian. I'll thry and get one from Dandenong.
Joe
-
20th September 2011, 11:17 PM #15.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Joe,
If you are able to obtain a spring and if it is as mine was, it will be coiled up and restrained with some heavy wire. It is under considerable tension and capable of causing injury should it be accidently untethered. I had a hell of a time trying to install mine. It had become unfurled and to rewind the thing involved making a slotted mandel to retain the inner end while I wound the spring around the mandrel, securing it progressively with the previously mentioned vise grips. Being dainty, I even resorted to wearing leather gloves during the procedure. If you are unfortunate to have a spring flay about, you will understand why.
Take care
BT
Similar Threads
-
Another Waldown
By Anorak Bob in forum METALWORK FORUMReplies: 5Last Post: 17th September 2011, 12:06 AM -
Something more relevant maybe? - Waldown Catalogues
By Anorak Bob in forum METALWORK FORUMReplies: 2Last Post: 21st July 2011, 01:42 AM -
tool post tart up
By toolman49 in forum METALWORK FORUMReplies: 3Last Post: 25th February 2011, 02:53 PM -
Hello and Waldown question
By craoni in forum GENERAL & SMALL MACHINERYReplies: 0Last Post: 2nd May 2010, 01:17 PM