Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 61 to 73 of 73
Thread: WTB: shaper in any condition
-
7th March 2012, 05:38 AM #61SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
As Ray said Joe, Welcome to the Shaper Club
Woodlee i'm sure , will be back on deck soon but if you like I could download another stick with the info on it and send it to you. I think there might be a couple of stops for the original before it gets to you. Or would it be better if whoever has the stick adds any extra info they might have and sends it on. Any thoughts??
Phil
-
7th March 2012 05:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
8th March 2012, 11:05 PM #62Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 54
-
8th March 2012, 11:41 PM #63
Hi Eric,
thanks for the link to the tender!
As I mentioned in post #59 above, my tender of $120 was accepted. So all up it will be around $425 by the time its in my shed.
Cheers,
Joe
-
9th March 2012, 06:04 AM #64Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 54
That is excellent! less than half what I paid for mine delivered. I am still in the market for another shaper. Especially another Douglas or smaller sized one. The one at Macksville was more than my transport organisation abilities could extend to especially since I am in South Australia.
I hope it arrives all in one piece.
Regards
Eric
-
11th March 2012, 03:50 PM #65"Outside of a dog a book is man's best friend ,inside a dog it's too dark to read"
Groucho Marx
-
11th March 2012, 04:46 PM #66SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
-
14th March 2012, 05:45 PM #67SENIOR MEMBER
- Join Date
- Jun 2004
- Location
- Kyabram. Vic
- Posts
- 826
Ray,
I heard a rumour the shaper & T&C grinder police struck town yesterday morning.
You wouldn't know anything about it would you????
I have organised to pick up that Macson Thursday pm. And wouldn't you know it; bludy thunderstorms predicted. I am sure they will happen as it's very black outside at the moment.
It would be s shame to see it get wet and cause "trailering" rust.
Ken
-
14th March 2012, 05:59 PM #68
Hi Ken, geez, it's getting hard to get in and out of Ky without tripping the alarm system these days..
It's a shame you didn't move it yesterday, it would have been perfect weather for it. I've got to detour by there again tomorow on the way to Tongala. I'd be thinking you might need a tarp by the look of the forecast.
Regards
Ray
-
19th April 2012, 09:22 PM #69SENIOR MEMBER
- Join Date
- Jun 2004
- Location
- Kyabram. Vic
- Posts
- 826
Well, the old lady Macson rolled back to life this afternoon. Stamped on it is 52/4. Most castings were stamped with a 2 except the toolholder which was 4. Somebody got it wrong. So raise your glasses and toast her 60th birthday.
She cleaned up pretty well with little wear in the slides. The only replacement parts needed was the ratchet pawl on the table feed. It has had a crash in the past that obviously damaged the pawl and took a tooth off the gear. The tooth had been repaired and the pawl filed back (unfortunately with a slope backwards and it wouldn't feed either way. I chose to make a new unit which needed a few stroke of a file to fettle it in. Works ok.
I was a bit concerned about the old electrics but they kept the magic blue smoke in. The contactor switch is a bit hit and miss. Chatters some times; nothing other times and at others just fires up. I used cleaner on them but will have to have a rub over.
Runs as smooth as and is super quiet. No movement even on top speed and a slightly uneven floor. Gave it about half an hours runin to bed moving parts in again. Well that's my excuse anyway.
Ken
-
19th April 2012, 09:43 PM #70
Ken,
The switch on Blondie is similar, except it goes on ok but doesn't always turn of. I pulled it to bits, cleaned etc but still no fix. I gave up. Later i re-attached the switch to the machine, and it works fine. Turns out it don't work when its flat on its back (no dirty jokes please, yes Phil (steamwhisperer) ,i mean you)
Ewan
-
19th April 2012, 09:43 PM #71Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 58
- Posts
- 2,557
-
19th April 2012, 10:14 PM #72SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
[QUOTE=Ueee;1476166 Turns out it don't work when its flat on its back (no dirty jokes please, yes Phil (steamwhisperer) ,i mean you)
Ewan[/QUOTE]
Bugga lol
-
20th April 2012, 08:38 PM #73SENIOR MEMBER
- Join Date
- Jun 2004
- Location
- Kyabram. Vic
- Posts
- 826
Bryan,
See the show us your shaper thread
Ken
Similar Threads
-
CD Condition
By clubbyr8 in forum MusicReplies: 3Last Post: 13th November 2008, 08:47 AM -
Advice re condition of cedar in pic
By Incoming! in forum TIMBERReplies: 14Last Post: 27th April 2008, 08:27 PM -
Another record 44 aparently in great condition.
By JDarvall in forum HAND TOOLS - UNPOWEREDReplies: 8Last Post: 5th April 2006, 06:10 AM -
A rare condition
By AlexS in forum WOODIES JOKESReplies: 0Last Post: 1st March 2002, 11:12 PM