Page 2 of 2 FirstFirst 12
Results 16 to 30 of 30
  1. #16
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by NathanaelBC View Post
    Couldn't quite make sense of 3M's product selector, looks like they were suggesting the "best" product for working with MDF are disposable 9913V filters that cost like $110 for a box of ten!
    The issue with significant exposure to MDF is not just the dust but the chemical components, the main one being formaldehyde which is a know carcinogen.

    Wood dust has a nominal Australian OHS exposure level based on Oak and Beech of 5 ppm for softwoods and 1 ppm for hardwoods but this does not include MDF which is 0.5 ppm. A new standard of 0.1 ppm has been talked about for some time. No one knows the toxicity of Australian timbers (not enough stats) but if anything they are likely to be worse than oak and beech.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #17
    Join Date
    Feb 2014
    Location
    Canberra, Australia
    Posts
    370

    Default

    But surely a P2/P3 particulate filter will trap the formaldehyde? It's not like it turns into a vapour ... so I'm curious why 3M specifically call out working with MDF and recommended one of their disposable masks not a 6000 or 7000 half mask or greater. Maybe because formaldehyde clogs up filters quickly so they're single use?

  4. #18
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by NathanaelBC View Post
    But surely a P2/P3 particulate filter will trap the formaldehyde? It's not like it turns into a vapour ... so I'm curious why 3M specifically call out working with MDF and recommended one of their disposable masks not a 6000 or 7000 half mask or greater. Maybe because formaldehyde clogs up filters quickly so they're single use?
    The formaldehyde is most definitely released as a vapour.
    Have a read of this https://en.wikipedia.org/wiki/Medium-density_fibreboard

    The more freshly minted, the higher the bit speeds used, the blunter the tool, the finer and warmer the dust, the more formaldehyde outgassed from the MDF.

    It is also recommended that ALL exposed MDF surfaces be sealed before being used as furniture as it will continue to outgas for years afterwards.

    All organic vapour filters are single or limited use - the organic vapour eventually saturates the absorber and it comes through the filter.

    This is where a high volume dust extractor really comes into its own. I can turn/sand a 10" MDF bowl without a face mask with my DC setup. I know I am not being exposed to the vapour because I have monitored the 0.3 micron dust being made during turning and the levels of this very fine dust are the same as the fresh air outside my shed. The finer the dust the more it behaves like a gas. 0.3 micron dust will ride the air currents coming away from a work piece which is the same pathway the formaldehyde will take.

    I lost my sense of smell for 6 weeks from working outside for a couple of weeks with MDF in 2002 and I do not want to go through that again. That, coupled with 30 years of research experience in building dust free research labs has give me a very useful background in this area. I was just a bit slow in connecting my day job with the woodwork.

  5. #19
    Join Date
    Nov 2011
    Location
    Riverina NSW
    Posts
    211

    Default

    I went through a similar search a few years ago to find a suitable mask or solution whilst respraying a car and found a razor was the only option. However, fast forward to more recent times for woodworking I'll trim the beard, sometimes, and will just crank in the adjustment straps of a half face mask. I did however find another solution on a boating forum that's cheap enough, the Resp o rator. Not sold in Aus I think, but it's got a mouthpiece like a snorkel with two tubes aiming backwards that attach filters. Looks simple enough and light, I just don't know how I'd go with a mouthpiece, let alone keeping it clean.

  6. #20
    Join Date
    Feb 2014
    Location
    Canberra, Australia
    Posts
    370

    Default

    Blackwoods had one of these on display on the counter: cleanspace-2 - CleanSpace

    1366127432_.jpg

  7. #21
    Join Date
    Nov 2011
    Location
    Riverina NSW
    Posts
    211

    Default

    Holy cow I just saw the price of those. They look and sound excellent but I'd never be able to justify the cost of some of the premium masks like that.

    The Resp-o-rator is below. Like I said, pretty simple setup. I was searching for images and saw a couple of custom jobs to imitate them. They cost about $45US but I still haven't found a seller in Oz. I dunno, they just seem like a good cheap alternative.

    resporator.jpg

  8. #22
    Join Date
    Apr 2002
    Location
    Brisbane
    Posts
    5,773

    Default

    This is not a new issue ....... the truth is simple and straight forward.

    For ANY half face respirator or mask to work, anything like effectively, the wearer must be recently clean shaven on the sealing area even a 5 oclock shadow can compromise sealing.... this is OHS gospel and is the truth.

    If you want to wear a beard and have even marginally effective breathing protection the only solution is a forced air full face shield.

    There is simply no way around this.

    If you think you are going to wear a beard with any mask or resirator that requires a seal and get anything like effective protection ...... sorry you are dreaming.

    cheers
    Any thing with sharp teeth eats meat.
    Most powertools have sharp teeth.
    People are made of meat.
    Abrasives can be just as dangerous as a blade.....and 10 times more painfull.

  9. #23
    Join Date
    Feb 2014
    Location
    Canberra, Australia
    Posts
    370

    Default

    Well, that's not going to happen ... the beard stays

  10. #24
    Join Date
    Apr 2013
    Location
    Macksville
    Age
    62
    Posts
    390

    Default

    I've noticed a few times lately that when sanding Jarah it's been irritating the inside of my nose. I have a full Ned Kelly type beard, which I've had for 35 odd years, so it's staying. Was thinking of getting one of these https://www.timbecon.com.au/extracti...-dust-mask-kit & was wondering if anyone else with a heavy growth of face fungus has tried them. I think they are the same as the ones Carbatec sell.
    I'm working in WA this week & was going to call into Timbecon on my way back to the airport & pick one up if they're any good.

  11. #25
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    4,464

    Default

    I only have a goatee but I bought this unit which, although it is not powered, looks a similar setup to the one you are looking at

    http://www.protectorsafety.com.au/ap...eated-timbers/

    Works well and seems to seal reasonably against the hair (put hands over filters and it activates the one way valves when you breathe in). Not a perfect seal as one would get on a shaven face but is better than nothing.
    Last edited by Lappa; 17th October 2016 at 08:59 PM. Reason: additional info

  12. #26
    Join Date
    Apr 2012
    Location
    Shepparton
    Posts
    140

    Default

    I have one of the trend pro powered dust masks and after initial head band breakage it works fine. One thing to keep in mind is the weight of the mask and how comfortable it is to wear for a period of time, if you can try the thing before you buy,is it suitable with glasses etc. good luck

  13. #27
    Join Date
    Nov 2006
    Location
    Wollongong
    Age
    75
    Posts
    77

    Default

    I have one of these Resp-o-rators. Had it for 5 years and it works extremely well with my full face beard. Does not obstruct vision, I can wear with glasses without them getting fogged up, ear protection doesn't get in the way and the filters are behind you. I replace the filter cartridges roughly every 6 months. I can highly recommend this. I got mine from these people resp-parent.htm
    All the best
    John (aka shep1)

  14. #28
    Join Date
    Nov 2006
    Location
    Wollongong
    Age
    75
    Posts
    77

    Default

    I should add that the device is very easy to clean and the filters are readily available from the supplier I mentioned

  15. #29
    Join Date
    Aug 2011
    Location
    bilpin
    Posts
    3,551

    Default

    Summer time and a full face positive force face shield.......Bliss.

  16. #30
    Join Date
    Jan 2013
    Location
    Tasmaniac
    Posts
    1,470

    Default

    Quote Originally Posted by rustynail View Post
    Summer time and a full face positive force face shield.......Bliss.

    Rustynail, can you post a picture of the abovementioned device?

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Replies: 5
    Last Post: 17th May 2016, 05:59 PM
  2. Seeking to Buy Full Face Respirator
    By thumbsucker in forum SAFETY
    Replies: 11
    Last Post: 13th October 2015, 05:31 PM
  3. Repairing Face Shield on Triton Respirator
    By GMsweeper in forum WOODTURNING - GENERAL
    Replies: 13
    Last Post: 18th August 2012, 10:43 AM
  4. 3M Half Face Respirator Recommended!
    By pellcorp in forum WOODWORK - GENERAL
    Replies: 15
    Last Post: 8th October 2010, 11:11 AM
  5. powered respirator, full face or 1/2 face??
    By old_picker in forum HAND TOOLS - POWERED
    Replies: 7
    Last Post: 13th December 2008, 09:58 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •