Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Jarrah slimline
-
9th February 2010, 01:23 PM #1
Jarrah slimline
I'm only new to this pen turning game but I think the bug has sunk its fangs in deep. I did a few over the weekend but forgot to photograph before giving them away to the inlaws. However this is last nights effort. The timber is Jarrah sanded to 600 and finished with Hut Wax.
I have a question for the more experienced of you out there. I lost a couple of pens over the weekend due to imperfections (maybe) in the timber (I think it was woody pear) that caused it to split. I've had a bit of a look around the forum re stabilising but still not sure how you go about saving something like that if you catch it before it has a chance to disintergrate. Any suggestions?
-
9th February 2010 01:23 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th February 2010, 01:40 PM #2
if you are turning and find a crack in the timber then you can put some CA glue into the crack and hit it with accelerator or just let it dry and that should hold
if you get one that blows apart and find all the pieces then you can also try glueing it back together with CA, sometimes it works and other times you can see the blow apart bits, but it is always worth a try, after all if it doesn't work you can always turn all the wood off the tubes and start from scratch
hope this helps
MIK
-
9th February 2010, 02:18 PM #3
nice looking pen. Very neat from end to end
I agree with MIK. Use CA. Sometimes it works, sometimes it goes pear-shaped. You can always start again... Annoying when it's expensive/rare/significant timber though.
When I buy pen I usually order some extra tubes for that style as there will always be times when you need them. You can also do a batch of pens on spare tubes, decide which ones make the cut and assemble them and turf the rest...
Cheers,
Dave
-
9th February 2010, 03:47 PM #4
Nice start to your new hobby.. Well done.
Reality is no background music.
Cheers John
-
9th February 2010, 09:16 PM #5Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Be warned!!! There is no cure, but that is agood thing.
Woody Pear, aka Hakea can be tempremental _ and dirty - but CA usually sorts it out, as Mik has already said.
Good luck.
-
11th February 2010, 06:38 PM #6
Hi Woodhacker,
Just a small tip.
When getting near the end of your fine chisel
or sanding work, place a clean sheet of paper
on the lathe below your pen.
If you have a relatively small problem you can then
recover some of the fine particles to patch up with
using some light superglue (c.a).
Sometimes it can actually add to the character
of the pen or easily blend in with burls.
AllanLife is short ... smile while you still have teeth.
-
11th February 2010, 11:49 PM #7Senior Member
- Join Date
- Aug 2003
- Location
- Perth WA
- Posts
- 357
May also be worth checking that you are getting good even spread of glue when putting in the tubes. There is very little timber left on a Slimline and this could be an issue too.
-
14th April 2010, 12:47 AM #8
What turning tool do most people use to turn pens???
I've typically used a roughing gouge, or even a fingernail bowl gouge for some of the 'trickier' timbers
... right now I hates Red Mallee ... has blown up on me twice ... grrrrrrrr
-
14th April 2010, 01:05 AM #9
Hey Woody,
Nice job on the Pen, and yeah you are hooked, watch out wallet ,
What all the other guys said about saving your blanks, is all first class advice, as for turning tools, what ever works for you is good, I use a gouge and sometimes a skew, some people only use a scraper, it doesn't matter what you use, no one will know once it's finished, and they wont be able to look at it and say oh he used a roughing gouge, The only thing that you have to have is a sharp tool, what ever it is.
HazzaBIt's Hard to Kick Goals, When the Ba^$%##ds Keep moving the Goal Posts.
Check out my Website www.harrybutlerdesigns.com.au
-
14th April 2010, 08:49 AM #10
Nice Job on the Pen, there are lots of frustrations with different materials we use,part of the learning process is knowing which ones will give trouble and take steps at the start of the pen making process ,eg which glue up for which materials, the more dificult stuff like very soft or burls need a top glueup I use 2 part epoxy for those, sometimes you will need to stabalise with thin CA as you get a bit closer to sizes It may help you to get some "hands on " with an experienced turner to get some fine pointers on using the notorious "skew" I know I only used mine for a scraper for the first year The one good thing is you can have a lot of fun and produce great pens along the way (we never stop learning ) and remember ,sandpaper is a turning tool lol, cheers ! John
G'day all !Enjoy your stay !!!
-
14th April 2010, 11:41 AM #11
Thanks for the advice Gawdelpus ... and of course you're right ... after taking a few deep breaths, I realised I probably should have taken it easier, with finer cuts, on the Mallee; particularly on the second occasion. One would think that I would have learnt from the first !?!
Skew Chisel ... it's an angled scraper isn't it ...
Yeah, I probably need to track down someone (locally) who knows how to use one properly. I've tried following guidance in a couple of books; one by Richard Raffan, but I still haven't quite got the knack yet ... and the gouges are just too easy to fall back to.
Similar Threads
-
Jarrah Burl platters and a Jarrah Bowl
By Willy Nelson in forum WOODTURNING - GENERALReplies: 10Last Post: 17th September 2009, 06:55 PM -
Slimline
By chrisb691 in forum WOODTURNING - PEN TURNINGReplies: 8Last Post: 1st November 2006, 10:13 PM -
She Oak, Jarrah, Wandoo, Marri, Old Growth Jarrah
By Taries in forum TIMBERReplies: 1Last Post: 22nd June 2006, 11:34 PM -
Jarrah Coffee Table, Jarrah Burl Bowl and other wood pics
By leighd in forum WOODWORK PICSReplies: 10Last Post: 17th June 2004, 10:08 AM -
Picking Jarrah from a Jarrah and Karri rack
By gmcginty in forum TIMBERReplies: 5Last Post: 7th December 2003, 11:52 PM