Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Lost bushing!!!
-
1st April 2009, 02:02 PM #1
Lost bushing!!!
Can I use the center from a pen?
-
1st April 2009 02:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
1st April 2009, 02:15 PM #2
A slimline bushing? You can use a centre, but it'll end up as no good for anything else.
If you have small pieces of brass, corian, hard(ish) plastic or even a some fine-grained pen offcuts, it's easy enough to make your own bushes.
- Andy Mc
-
1st April 2009, 05:43 PM #3
eliza u can get new bushings from qld w/working supplies or carbatec in brissy or source them interstate carrols , addictive
-
1st April 2009, 05:52 PM #4
Yes, I'll get new ones tomorrow. Just that TODAY was the day put aside for pen turning!
I managed to get a few done, just turned it over half way through!
-
1st April 2009, 07:43 PM #5SENIOR MEMBER
- Join Date
- Sep 2008
- Location
- Maryvale, Queensland
- Posts
- 2,338
Just turn down a small piece of wood if nothing else. 6.5mm is about the bit size to fit an "A" mandrel, then just turn it down to the dimensions for the required bush, as long as you have a micrometer or something, you can get the sizes off one of the supplier sites somewhere.
Russell.Pen Affair Craft Supplies - Cheapest Pearl Ex & Pemo Polymer Clay in Australia
http://craftsupplies.penaffair.com
-
1st April 2009, 07:51 PM #6Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
David was loading his truck today. May not be there tomorrow.
-
1st April 2009, 08:38 PM #7
-
1st April 2009, 10:09 PM #8
I have a very useful tool called a floor sweep - it is a magnetic 'broom' type thing from Bunnings ~ $13. The main surface is a magnetised and about 15 x 5 cm and then the end of the handle it also a magnet. I use it mostly to pick up nail bits after the farrier has been but it is also very handy for finding things on the floor and in among shavings. Might be worth considering.
JD"No point getting older if you don't get smarter"
-
1st April 2009, 10:21 PM #9
I've used a metal detector to find a lost chuck screw
tried to find a 1A bush once with it - no luck - but then it had rolled/bounced across the other side of the (tidy) shedregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
1st April 2009, 10:30 PM #10
advantage of having a metal lathe as well. Just make a new one.
-
2nd April 2009, 07:23 AM #11SENIOR MEMBER
- Join Date
- Sep 2008
- Location
- Maryvale, Queensland
- Posts
- 2,338
I was putting a Churchill together last weekend and once again, the suppliers stuck all the wrong parts together in the packets. So I was pulling them all apart and the tiny little decorative silver ring flung off and rolled under my workbench with all the shavings and random bits of wood. 5 minutes of swearing and carefully moving 1 bit fo scrap at a time, and it showed up thank goodness. Not sure a magnet or metal detector would have picked that one up.
Russell.Pen Affair Craft Supplies - Cheapest Pearl Ex & Pemo Polymer Clay in Australia
http://craftsupplies.penaffair.com
-
2nd April 2009, 05:04 PM #12
It's when those little doodads fall down the 4" duct... and you can hear the rattle, clunk, tinkle, rattle through the ducts as it makes it's way towards the impeller on your DC that the cussing really starts.
Even worse when it's the screws from your chuck jaws...
- Andy Mc
-
2nd April 2009, 05:19 PM #13Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
-
2nd April 2009, 05:27 PM #14
I gave up trying to make an efficient pickup for while I was turning, so I settled for a floor-sweep under the lathe.
That's just a scoop that sits on the floor, so you can sweep your curlies straight into it. (Along with everything else that fell on the floor.)
Of course, Murphy's Law dictates that any small screw, fitting or whatever I dropped always fell directly in front of the sweep and... SLUUURP!
- Andy Mc
Similar Threads
-
Bushing sizes for pens.-
By PenTurner in forum WOODTURNING - PEN TURNINGReplies: 16Last Post: 21st October 2008, 08:03 PM -
Brass Router Bushing Set - keeping it in tight
By old_picker in forum ROUTING FORUMReplies: 5Last Post: 8th October 2007, 10:09 AM -
tight bushing
By burraboy in forum METALWORK FORUMReplies: 3Last Post: 25th September 2007, 09:35 PM -
TSC10HB, 30-16mm bushing reducer tightness
By mcarthur in forum WOODWORK - GENERALReplies: 11Last Post: 21st February 2007, 03:25 PM -
Bushing a elec motor shaft.
By Harry72 in forum METALWORK FORUMReplies: 11Last Post: 23rd October 2005, 11:41 PM