Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: playing with plating...
-
7th June 2009, 02:14 PM #1
playing with plating...
In between dye jobs I have been playing with electro-plating copper to hardware...the idea is to custom plate some select kits for small custom lots and customers..
Copper is simply the starting point, the hope is to go to chrome, (depending on the required chemicals), also real gold, nickel, and sterling silver.
Below is a prototype experiment, plated the shells as well as the hardware, and fit was not a concern, it was simply to see if it worked as I hoped it would.
Comments and ideas always welcome...pro and con.
No real effort was put into a polish, simply Mothers Mag polish, as this will be disassembled by the time you read this thread...I have a vibrating polisher and the proper medium to do a good sized lot of parts, so I didn't get too carried away on the prototype.Last edited by edblysard; 7th June 2009 at 02:15 PM. Reason: I can't spell worth a hoot after 10pm...
-
7th June 2009 02:14 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
7th June 2009, 03:07 PM #2Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
That has worked out very well.
Do you intend to test the durability of the plating Ed? If so, how?
-
7th June 2009, 03:18 PM #3
super
troy
-
7th June 2009, 07:06 PM #4
Do tell us how!
-
7th June 2009, 07:27 PM #5
Another good one, there will be refining along the way, can the same set up be used for other metals? I imagine different metals will need different chemicals for electrolysis to occur. Amos
Good, better, best, never let it rest;
Til your good is better, and your
better, best.
-
7th June 2009, 08:53 PM #6
-
7th June 2009, 08:56 PM #7
-
7th June 2009, 10:56 PM #8
Ed, I like what you have done, you can plate the whole bullet, nib, cb, clip and finial. Nice to accent the brass and nickel cartridges with copper nibs, cb's and clips. It opens up a lot of different options. Will wait to see you come up with more.
Cheers
Darren
-
7th June 2009, 11:08 PM #9
-
8th June 2009, 02:43 AM #10
Plating is a fairly easy process, but it can get expensive real quick. Especially getting into gold and sterling. Also need to be careful with the cyanide.
There are coatings to apply that keep it from tarnishing.
-
8th June 2009, 06:30 AM #11
Found out something rather odd, or maybe not...
Was washing a few of the nibs from the "cheap" 7mm kits in lacquer thinner prior to plating them...the "gold" plating on them pitted, and on a few, washed away completly...so I slapped the old volt ohm meter to one and surprise...it ain't plated at all, its painted with a plastic gold paint over a brass nib....it does have a slight metal content, it registers on the meter, but nothing like the nibs from the better kits...so a few seconds with an Xacto knife confirmed that the plating was indeed metalic gold paint.
I imagine it is a powder coating of some type.
So...to plate the cheap kits might require a dip in some type of stripping compound to take them to the brass....did discover that the better kits with real gold do take the copper plaing quite well...as with any finish, the better the surface is preped, the better the end result will be...also discovered the better kits are brass hardware plated with copper, then gold, chrome or nickel...the copper plating acts as a "primer" base for the gold or nickel and such to adhere to...and the opposite works just as well, the light gold plate offers a perfect surface to copper plate.
Chrome does not accept the copper plating, neither does nickel, the acid reaction required for the plating dosen't affect the chrome or nickel.
-
8th June 2009, 08:42 AM #12Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Welcome to Alchemy 101!!
-
8th June 2009, 07:44 PM #13
-
8th June 2009, 09:02 PM #14
Just a copper sulfate and sulfuric acid solution...and a small transformer.
Out put on the transformer is 3 volts at 100 milliamps.
Anode (+) is a piece of copper plate, the part to plate is the cathode (-)
Agitate and it takes about 5 minutes to build up a good thick layer.
Similar Threads
-
Zinc Plating
By bosun in forum METALWORK FORUMReplies: 5Last Post: 8th May 2009, 03:41 PM -
plating
By schaf in forum WOODTURNING - PEN TURNINGReplies: 3Last Post: 6th October 2008, 09:48 AM -
removing nickel plating?
By R.B. in forum HAND TOOLS - UNPOWEREDReplies: 9Last Post: 13th December 2007, 10:26 AM -
removing old plating
By old_picker in forum METALWORK FORUMReplies: 1Last Post: 30th May 2007, 04:15 PM -
Nickel plating
By Clinton1 in forum METALWORK FORUMReplies: 10Last Post: 6th January 2006, 08:53 AM