Results 1 to 6 of 6
  1. #1
    Join Date
    Jul 2022
    Location
    Gympie, QLD
    Posts
    35

    Question how to extend timber uprights

    Someone gave me a pre-owned "kit" cubby house. As you can see from the photos, the uprights -- once concreted in -- are not at the same height. (The three posts in the middle are supposed to be a lot higher than the others; it's a basic gable roof.)

    20221112_102904.jpg


    Initially, I thought I'd just cut them down to the height of the shortest post, but I think that might make it too small/low for my kids.



    Next, I thought I'd cut them down to the height of the shortest post and attach post stirrups on the top (y'know, the kind used on verandahs), but that wouldn't be very strong going into the end-grain on the posts.



    Then, I wondered whether I could:
    • cut them down to the height of the shortest post
    • drill a hole about 250mm into the top of the post
    • insert some rebar
    • then, get another post the same diameter
    • cut lengths to the desired height (I'd say probably 600mm)
    • drill a hole down the centre
    • slot it onto the rebar
    • and add bracing/strapping on four sides about 200mm on each side of the join.




    My latest hair-brained idea is to "sister" them in some way... not sure how... perhaps cut away half the top of the post (say, 500mm), do the same with the extension piece, then drill two or three holes through both and bolt them together with M10 or M12 bolts.



    That all sounds rather complicated, though... surely there must be a simpler way?

    Thanks very much for any advice you can offer this stuck dad.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    May 2012
    Location
    Woodstock (Cowra)
    Age
    74
    Posts
    3,373

    Default

    3 pieces 50 x 6 flat bar 600 long per post (300mm lap on post and extension) , 2 bolts 10mm dia each post, total 4 bolts per piece of flat bar, all galvanised because you are dealing with treated pine
    The person who never made a mistake never made anything

    Cheers
    Ray

  4. #3
    Join Date
    Jul 2022
    Location
    Gympie, QLD
    Posts
    35

    Default

    You, sir, are a champion. Thank you!

  5. #4
    Join Date
    Jul 2022
    Location
    Gympie, QLD
    Posts
    35

    Default

    One question, though, Ray... why three pieces per post?

  6. #5
    Join Date
    May 2012
    Location
    Woodstock (Cowra)
    Age
    74
    Posts
    3,373

    Default

    Anything in a triangular configuration is the strongest, forces equal in all directions
    So 3 pieces 120deg apart on circular posts = 360deg
    Instead of bolts use 50mm x 10mm coach screws, no problems of alignment that way
    The person who never made a mistake never made anything

    Cheers
    Ray

  7. #6
    Join Date
    Jul 2022
    Location
    Gympie, QLD
    Posts
    35

    Default

    It worked like a charm, Ray. Thank you!

Similar Threads

  1. Replies: 18
    Last Post: 10th November 2015, 05:01 PM
  2. How do I extend....
    By TORB in forum WOODWORK - GENERAL
    Replies: 0
    Last Post: 10th December 2011, 05:01 PM
  3. Shelving span between uprights
    By LanceC in forum THE SHED
    Replies: 6
    Last Post: 1st November 2011, 01:37 PM
  4. Help to extend a rip fence
    By gwambygine in forum WOODWORK - GENERAL
    Replies: 9
    Last Post: 3rd May 2009, 04:31 PM
  5. how do you extend an IP hole?
    By ubeaut in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 0
    Last Post: 16th November 2008, 07:10 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •