Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 5 of 5
  1. 7th November 2007, 08:29 PM #1
    peter_sm
    peter_sm is offline Senior Member
    Join Date
    Dec 2006
    Location
    Outer East - Melbourne
    Posts
    316

    Default Operating instructions for HPM sensor light.

    I have a HPM sensor light in the garage. It is a round tennis ball sized sensor 180 degrees hooked up to a flouro light. It has a timer and a lux adjustment. It has an on off switch on the wall.

    From what I can find it is a HPM 630/3. There are no operational instructions I can find on the HPM website or anywhere else.

    My question is. How do I make it stay on? - and then resume sensor operation?
  2. 7th November 2007 08:29 PM # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. 7th November 2007, 08:37 PM #2
    patty
    patty is offline Senior Member
    Join Date
    Jun 2007
    Location
    In a House
    Posts
    353

    Default

    usually with these units you switch them off at the light sw then on within a few seconds for the unit to stay on all the time for it to go back into sensor mode you usually turn it back off wait about 30 seconds maybe more the turn back on and they go automatically back into sensor mode
  4. 7th November 2007, 08:39 PM #3
    patty
    patty is offline Senior Member
    Join Date
    Jun 2007
    Location
    In a House
    Posts
    353

    Default

    this is not a sensor light it is just a sensor correct i think i may have a copy of the instruction sheet downstairs in the shed but it is pissin down raining at the moment if i find it i will scan it and email it to ya!
  5. 7th November 2007, 08:51 PM #4
    patty
    patty is offline Senior Member
    Join Date
    Jun 2007
    Location
    In a House
    Posts
    353

    Default

    Instruction book found
    Manual Override
    There will be times when you wish the light to stay on regardless 0of motion.This is achieved by turning the switch off and on again within 2 seconds the light will ow remain onuntil manually switched 'off' to return the light to sensor or auto mode turn the switch off for longer than 5 seconds and then switch back on..

    And that is straight from the installation and opeaing instructions for a HPM 630/3
  6. 7th November 2007, 10:01 PM #5
    peter_sm
    peter_sm is offline Senior Member
    Join Date
    Dec 2006
    Location
    Outer East - Melbourne
    Posts
    316

    Default

    Bingo. That is exactly what I was after. Very appreciated, thank you very much.
« Previous Thread | Next Thread »

Similar Threads

  1. Who reads instructions?
    By Colin Howkins in forum HAVE YOUR SAY
    Replies: 37
    Last Post: 25th October 2007, 02:52 PM
  2. Just follow the Instructions, (and pictures too)
    By Matt88s in forum WOODTURNING - PEN TURNING
    Replies: 5
    Last Post: 6th May 2007, 05:52 PM
  3. Read the doggone instructions
    By ScrollZilla in forum WOODTURNING - PEN TURNING
    Replies: 10
    Last Post: 3rd April 2007, 07:25 AM
  4. Parkerizing instructions
    By Grahame Collins in forum METALWORK FORUM
    Replies: 11
    Last Post: 22nd December 2006, 07:34 AM
  5. Where can I get a new operating system for my computer for free ?
    By JDarvall in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 45
    Last Post: 1st February 2006, 04:51 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules