Results 1 to 14 of 14
  1. #1
    Join Date
    Feb 2016
    Location
    Canberra
    Posts
    5,124

    Default "Thin" extension cables?

    Hi all electrical wizards,

    I posted this question a while back - New power point fed from AirCon Isolator Switch? about putting an power point on an aircon circuit. No go.

    The dills who built these units have no provision for external power. Christ I hate cheap buildings.

    Annnnyyyway... I can run an extension cable out of a window, but was hoping to find the flattest one available.

    Seems they aren't made*

    Reason for wishing a flat one? So I can close the window in summer (40°+) and winter (-4° last night).

    Other than having someone making one up using some electrical cable, does anyone know of a reseller of flat extension cables?

    They must exist... running under rugs, in lounge rooms, conferences etc....

    I cant find them anywhere!



    * for Aust that is...e.g. of what Im after: Slimline 2241 Flat Plug Extension Cord, 3-Wire, White and Convention Center Flat Extension Cord

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Apr 2007
    Location
    Sydney
    Posts
    749

    Default

    The 5mm or so you will save is not going to make much difference to your heating & cooling.

    Better option would be to use a window insert to fill the gap, and create a hole/notch in the insert for the cable. That is non destructive (in case you are not the unit owner) and will seal the gap so you minimise any issues in heating & cooling.

    What type of windows is it? For sliding windows it is super simple to make a filler, and easy to set it up so its secure. Hopper or casement windows are a bit trickier, but do-able.

    If you own the unit, then you could simply drill a 10mm hole in the windows frame or the wall. Remove the plug from one end of the extension cord , feed it through & re-assemble it (to be perfectly compliant, you could get a sparky to re-join the plug)

  4. #3
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by woodPixel View Post
    They must exist... running under rugs, in lounge rooms, conferences etc....
    I always though it was definitely not code to run extension cords under rugs?

    Never seen one at conferences either - Conferences use standard round cable and a flat triangular ramp up-down with slot for round cable

    They're probably not up to aussie code?

  5. #4
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    4,464

  6. #5
    Join Date
    Jun 2010
    Location
    Bundaberg
    Age
    54
    Posts
    3,402

    Default

    Quote Originally Posted by Lappa View Post
    That looks like solid core; what is needed here is flex cable.

    I don’t think I’ve ever seen flat flex in 3 core. I do like RossM’s suggestion to simply fit a solid spacer in the window; the only issue I can see would be with whatever window locking arrangements are currently fitted but there’s generally nothing that can’t be improvised.
    Nothing succeeds like a budgie without a beak.

  7. #6
    Join Date
    Feb 2016
    Location
    Canberra
    Posts
    5,124

    Default

    Lappa, this is exactly what I was thinking.... but I'm sure the sparkies would have a fit over it.

    Yes, I'm renting. Its a curse, but its one I need to live with right now. When life pulls you into a rip, its best not to fight it.

    On the windows, RossM, they are bottom opening hoppers. They have a wee bit of rubber sealing extrusion around the edge, but not a lot. I really don't think they will close enough, its a bummer about the design.

    I think the flat design to run under carpets must be "against code" as well, from the fact they aren't buyable. It seems odd though, for I've seen MANY cables tucked right up hard under the edges of cables along walls, especially in older Sydney houses (god some of those 40's and 50's inner city places are shitholes).

    Thanks for the advice all. Such a stupid little problem that's causing me a big headache.

  8. #7
    Join Date
    Oct 2015
    Location
    Ringwood, VIC
    Posts
    575

    Default

    What about adding a thick rubber seal along the sill - window can seal against it with room for the cable.
    Thick tape

    Maybe a dowel above the window to prevent it being opened if you can't lock it.

  9. #8
    Join Date
    Apr 2007
    Location
    Sydney
    Posts
    749

    Default

    Quote Originally Posted by woodPixel View Post

    On the windows, RossM, they are bottom opening hoppers. They have a wee bit of rubber sealing extrusion around the edge, but not a lot. I really don't think they will close enough, its a bummer about the design.
    OK. Run a normal extension cord through the window & close it as much as possible.
    Measure the gap at the side, and measure the height of the window. This will define a long, narrow triangle.
    Measure the width of the window. Together with the gap, this will define a rectangle.
    Go to Bunnings and buy this:
    Knauf Insulation 30 x 600 x 1200mm XPS Multi-Use Foam Board
    Cut out two of the triangles and the rectangle you measures above. Fit these into the sides and bottom of the window. This will allow it to remain ajar, but sealed from drafts. You could glue the pieces together, but probably not necessary.
    Cut a notch in the corner of the foam to allow the cord to pass through.
    (if needed, you can glue foam to get longer than 1200mm)

  10. #9
    Join Date
    Apr 2007
    Location
    Sydney
    Posts
    749

    Default

    If you get landlord permission and have the cash, you could get a sparky to run a new powerpoint from an exiting GPO circuit. It's possible that the conduit for the a/c has room to pull another cable. Would need investigation, and may be pricey.

  11. #10
    Join Date
    Feb 2016
    Location
    Canberra
    Posts
    5,124

    Default

    Quote Originally Posted by RossM View Post
    If you get landlord permission and have the cash, you could get a sparky to run a new powerpoint from an exiting GPO circuit. It's possible that the conduit for the a/c has room to pull another cable. Would need investigation, and may be pricey.
    LL is very responsive to any improvements. Permission obtained.

    Had a bloke here when we moved in (place had two dud GPOs) and he looked at it and said... "yyyeeeeaaahhh nnnaaahhhhh. It would cost a bomb mate".

    I'd figured he was softening me up for a Bull$hit Number

  12. #11
    Join Date
    Jul 2011
    Location
    In between houses
    Posts
    1,784

    Default

    Just drill a hole through the mortar between the bricks push the cable through, put the plug on. Easy to patch the mortar up when vacating. Selleys sell different colours tubes of goo to patch mortar, done ot heaps of times.

  13. #12
    Join Date
    Nov 2012
    Location
    SE Melb
    Age
    64
    Posts
    1,277

    Default

    Just choose the location of the external GPO to be as close to the other side of the wall of an internal GPO. A short piece of wire, and pierce the damp proof course. Should be a half-hour job. 200 bux would be my estimate. 75 bux for half hour labour. 40 bux for GPO and cable. 50 bux for travel there and back, the extra is for being a small job.

  14. #13
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    4,464

    Default

    Quote Originally Posted by Chief Tiff View Post
    That looks like solid core; what is needed here is flex cable.

    .
    Looks like multi stand to me.

    A94724D1-9A7F-4F19-9FCD-594B4543A0B7.jpg

  15. #14
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    That 4 core flat cable looks like standard fixed installation TPS cable.

Similar Threads

  1. Plastic "Bung Taps" - I want to "click" a garden hose onto the end of one...?
    By Batpig in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 4
    Last Post: 7th May 2017, 04:05 PM
  2. Why do so many "private" eBay sellers only offer "local pickup"?...
    By Batpig in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 27
    Last Post: 16th July 2016, 08:57 PM
  3. New Alternative Accelerator for Thin CA - "Super Tight As Method"
    By timberbits in forum WOODTURNING - PEN TURNING
    Replies: 13
    Last Post: 12th December 2011, 09:47 AM
  4. eBay: How long can you "Save" the "Draft"-listing of an item you want to sell?...
    By Batpig in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 0
    Last Post: 22nd January 2011, 06:04 PM
  5. Super Super "THIN" fiberglass cloth....
    By HammaHed in forum TIMBER
    Replies: 0
    Last Post: 7th February 2010, 01:07 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •