Page 2 of 2 FirstFirst 12
Results 16 to 24 of 24
  1. #16
    Join Date
    Sep 2008
    Location
    North Carolina, USA
    Posts
    2,327

    Default

    Peter,

    If the bearings sound good, you might want to use one of these:

    1/2" Power Twist Plus Link V-Belt - Rockler Woodworking Tools

    They are reputed to run smoother than a regular V belt and can be installed without removing the spindle.

    You might first try rubbing your existing belt with a rag soaked with rubbing alcohol, giving the running surfaces a rub with 220 grit sand paper, and increasing the tension on the belt.

    If a belt has gotten stiff and set from sitting for years, often a 10 minute run at medium speed will warm it enough to make it run smoothly.

    It is best not to drive the spindle out. Banging on the shaft may damage the bearings by making dents in the running part with the balls or rollers. Better to pull or press out with a long bolt or timber and long clamps.

    Be sure to check for one grub screw under the first one in each hole. When the area on the shaft appears where the grub screw has bitten, sand off the raised ridge. Use lots of penetrating oil on everything.
    So much timber, so little time.

    Paul

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #17
    Join Date
    Nov 2015
    Location
    Whangarei, New Zealand
    Age
    70
    Posts
    282

    Default

    Things turned out to be more wonky that I was aware of. I had a look at the shaft opposite the bed of the lathe,
    and that runs true, no wobble in it at all. However ...
    ... up against the bearing there's a recess milled into the shaft that holds a split bush that presses against the bearing.
    over the top of that sits yet another bush that holds the split bush in and comprises a register of sorts.

    IMG_0810.jpgIMG_0811.jpgIMG_0814.jpg

    But, as you can see, that register is nowhere near the faceplate. The faceplate sits up against nothing. That is, what my
    friend had done was to put a grindstone in there with a couple of washers (and fat paper disks on the grindstone) so
    of course it would be somewhat loony to expect that to be wobble free ... which apparently it was for him, but certainly
    not for me.
    Even the face of the outer bush is not wobble free as it were. I am at a loss as to how to actually get a register here that
    the faceplate (or a chuck) can ride against. There's a huge gap between the bearing and the thread on the spindle.

    This is how he had it set up when I got the lathe:

    IMG_0815.jpg

    Sadly, the register on the other side of the shaft, facing the bed, is no better. It's seriously scarred and looks like it's actually
    been attacked with a cold chisel. The MT drive centre is fine, but I can't get a chuck on there either, I think, without taking the
    whole thing to an engineer and getting it rebuilt. It does not look like that face can be undone from the shaft at all.

    I was very much hoping to be able to mount a chuck on this thing. The lathes bed and housing is in very good nick, very solid,
    very heavy, bearings are good, even though it does not have a variable speed motor.
    I don't think I do enough turning to warrant replacing it with a midi lathe.

    <sigh>

  4. #18
    Join Date
    Nov 2009
    Location
    Oxley
    Age
    50
    Posts
    438

    Default

    Hi PWH

    Not sure of the relative ages of our two lathes or if something is missing from your one but mine has a slightly different arrangement on the outboard end. As you can see from the pic mine has an extended collar that fits over the split bush and goes all the way back to the threads to provide a surface to register against.

    Not much help for your problem though I'm afraid.

    cheers
    WH
    Attached Images Attached Images
    I don't suffer from stress, but I have been told I'm a carrier

  5. #19
    Join Date
    Nov 2015
    Location
    Whangarei, New Zealand
    Age
    70
    Posts
    282

    Default

    Well yes, actually, that gives me a clue. Presumably my mate has dropped a piece so he could do his thing
    with the grindstone. I guess if I go and see an engineer with a metal lathe, something might be done about
    this.

    thanks -P.

  6. #20
    Join Date
    Nov 2009
    Location
    Oxley
    Age
    50
    Posts
    438

    Default

    Let me know if you need any more details pics to show the engineer.

    cheers
    WH
    I don't suffer from stress, but I have been told I'm a carrier

  7. #21
    Mobyturns's Avatar
    Mobyturns is offline In An Instant Your Life Can Change Forever
    Join Date
    Jul 2012
    Location
    "Brownsville" Nth QLD
    Age
    66
    Posts
    4,413

    Default

    The insert / chuck design on Nova chucks uses the nose of the spindle thread to register the chuck, so you could true up the spindle nose & use Nova chucks.
    Mobyturns

    In An Instant Your Life CanChange Forever

  8. #22
    Join Date
    Nov 2015
    Location
    Whangarei, New Zealand
    Age
    70
    Posts
    282

    Default

    That is excellent news, indeed. Thank you for the heads-up.

  9. #23
    Mobyturns's Avatar
    Mobyturns is offline In An Instant Your Life Can Change Forever
    Join Date
    Jul 2012
    Location
    "Brownsville" Nth QLD
    Age
    66
    Posts
    4,413

    Default

    Quote Originally Posted by P.W.H. View Post
    That is excellent news, indeed. Thank you for the heads-up.
    Peter my response was a little tongue in cheek as a lot of turners use their Nova chucks in that manner and then wonder why they get problems with vibration.

    All chucks need to "register" the chuck (or insert) to the spindle to maintain accurate running, so it is important that we protect both the spindle thread and the "registration surface" which is generally a machined flat surface on a wood lathe spindle.

    It is true that the inserts on Nova chucks register the nose of the insert thread to the inside face of chuck body at the bottom of the insert thread in the chuck body. Vicmarc inserts register the two flats on the rear face of the chuck body to the boss on the insert. However the rear of both Vicmarc and Nova inserts should reach and be nipped to the "register" on the lathe spindle.

    Problems arise when the spindle nose thread is longer than the depth of thread in the insert which means the nose of the spindle binds to the bottom of the insert/chuck thread before the registration surfaces actually meet. Nova inserts and more so their direct threaded chucks have a relatively short thread which means they are quite often used incorrectly - which is what I was having a little dig about.

    Nova / Teknatool actually advise turners to check this in their manuals and if necessary have an accurate spacer machined so that the chuck registers to the spindle register via the spacer.
    Mobyturns

    In An Instant Your Life CanChange Forever

  10. #24
    Join Date
    Nov 2015
    Location
    Whangarei, New Zealand
    Age
    70
    Posts
    282

    Default

    Right, and a good dig it was, too ) Thanks for taking the time

    We'll just have to see. My wife made the pertinent comment "And what are you going to do with all those bowls?"
    and she's not at all off the mark: there are a LOT of woodturners in these parts and I would be doing it casually at
    best, I have more passion for designing and building furniture - my attempts at turning are more in the way of my
    usual "I want to get a handle on how that works" diversions.

    So I'll give this a little rest ... getting a sleeve machined that can be a good register for a chuck should not be too
    much of a problem on the bed side of the lathe. The outboard side is a mite suspect.

    -P.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Replies: 23
    Last Post: 17th April 2014, 10:22 PM
  2. Small Lathe - Identification parts or advice needed
    By Squirrel in forum GENERAL & SMALL MACHINERY
    Replies: 3
    Last Post: 27th April 2011, 10:25 PM
  3. Just a bit Wonky.....
    By Stu in Tokyo in forum WOODTURNING - GENERAL
    Replies: 12
    Last Post: 8th August 2007, 12:47 AM
  4. Lathe advice needed - Jet/Carbatec
    By Rookie in forum WOODTURNING - GENERAL
    Replies: 14
    Last Post: 23rd August 2006, 06:50 PM
  5. Lathe advice needed
    By mrmac_6 in forum WOODTURNING - GENERAL
    Replies: 3
    Last Post: 3rd July 2006, 11:40 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •