Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 20 of 20
Thread: bolting down a lathe
-
12th April 2013, 02:05 PM #16GOLD MEMBER
- Join Date
- Aug 2007
- Location
- Saskatoon, SK, Canada.
- Posts
- 1,439
Those of us here in the Great White North that don't have in floor heating open the door to the shop and pour a little water on each foot of the lathes base. A few minutes later it's frozen to the floor and we can turn to our hearts content secure in the knowledge that the lathe isn't going anywhere until early summer when it thaws. A few weeks later and we can repeat for another year of turning.
Pete
-
12th April 2013 02:05 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th April 2013, 12:30 AM #17Member
- Join Date
- May 2010
- Location
- Acme Alberta Canada
- Posts
- 80
You nailed that one,Pete. On April 9 I turned 55 and got up to see the thermometer at -13C, and its been like this since the middle of Octember. You know what they say bout living on the prairies: 6 months of winter and the rest is tough sledding! Anyway, that is why we have heated shops. A while ago the guys down under were talking bout the opposite end of the spectrum, I think my blood is too thick for that. Although I would risk it for a while after this winter, it hasnt been super cold(-32c) or so but it doesnt want to leave.
-
15th April 2013, 12:06 AM #18
bolting down a lathe
50 mm penetration into the concrete should have been enough, 75mm would be over kill. The 100mm bolt (assuming the foot is flat and a nominal 3mm plate) would run the risk of punching right thru the concrete and blowing it out.
Sounds like you may have hit some reo. Try moving your lathe 50 mm diagonally if you can and drill again.
The suggestion to blow out the hole is an excellent one.
-
15th April 2013, 12:10 AM #19
bolting down a lathe
On pulling out the old dynabolts. You may find the 100mm bolt is a 2 piece sleeve, the main sleeve and a shorter one to make up the length. In this case if the main sleeve is below the surface you will have extreme difficulty removing the bolts.
-
15th April 2013, 12:31 AM #20
My first question is do you really need to bolt it down?
My lathe weighs about 70 kg - it sits on a stand of steel that weighs about 30kg....I stack timber on the same stand and I have 4 X 20kg bags of concrete on the shelves.
As a result of all this weight I can't even budge it, let alone have any movement from turning...
So if you have enough weight down low you really shouldn't have much movement....
But hey....what do I know...
My 0.02c worth...
Similar Threads
-
A Bolting iron
By auscab in forum HAND TOOLS - UNPOWEREDReplies: 9Last Post: 28th June 2013, 07:06 PM -
HEADS UP Wood lathe:jet 1220 midi lathe
By Woodwarehouse in forum ANNOUNCEMENTSReplies: 0Last Post: 1st December 2011, 03:02 PM -
Converting a Metalworking Lathe to Wood Turning Lathe
By GrinlingGibbons in forum WOODTURNING - GENERALReplies: 13Last Post: 29th March 2011, 07:17 AM -
Buying a lathe (Old massive Lathe, or New small C6 Lathe)
By Ch4iS in forum METALWORK FORUMReplies: 5Last Post: 25th March 2009, 12:19 PM