Thread: Give something back - a bowl

Intriguing piece. Visually captivating - it keeps dragging my eyes back to it. I think your farmer is going to be quite tickled.

Mate!!
That is gogeous!

Lovely little piece Dave, nice shape and good use of the natural edge. As for the grain

Happy birthday to you Dave - just noticed!

Lovely bit of grain there David and a nice job of presenting it T'is exactly why I always go the crutch!!! - cannot find better figure in a tree.

Originally Posted by Calm

Some one on this forum once posted that they always give something to the generous supplier of wood.....................

Might have been me - think I've mentioned before our long-standing family tradition of making something in gratitude to the giver of wood (except other woodies of course who can bloody well make their own!!)

Great piece of timber! darn good job on the bowl to boot.

Nah to the hollower your doing alright just with what you've got

Nice piece David. Even better that it was saved from the fireplace!

Amazing grain.

HB Dave.

Nice looking bit of timber.

What were you using inside that was catching?

The next step you have to take on this turning journey is cleaning up the chuck mount in the foot.
It is not easy with a natural edge piece like that but it can be done & you don't have to spend a fortune on a special bit of gear to do it.

When you first turn the chuck mount, clean up the base as good as you can get it without sanding off the dovetail for the jaws & leave a small flat top tit in the middle with a slight mark for the centre.

Once you have finished the piece, grab a block of junk timber, mount it in a chuck & make a former that will fit inside the bowl.
Cover the former with something soft like a piece of cloth or a bit of router mat rubber, put the piece over it & bring the tail stock up to the little dent in the centre of the bottom to hold it in place.
Now, with a low speed & a light touch from a sharp tool, turn away the dovetail & finish the bottom.
Once you have finished everything but the centre tit, remove it from the lathe & carve the tit off with a sharp knife or chisel.
Hand sand the cut & finish that too.

Thanks everyone - just woke up form a snooze on the couch. 17 1/2 YO daughter says its a "nanny nap", must be the age.

It is about 7 inches across and 2 1/2 maybe 3 inches deep from the highest point. I used a HT 1/2 and 3/8 bowl gouges (badly sharpened) and a 1/2 inch round nose scraper. I think the catches were from the grain running in so many different directions but with a "high point" coming round near my fingers 500 times a minute i could see it all finishing in pain (all to me) so it ended up being a bit chunky.

Cliff you are spot on i need to finish the bottom off properly. I normaly sand and finish the outside before i turn it around but i used epoxy on all the cracks after i shaped the outside. While it was 1/2 dry i started the inside then of course i hadn't done the bottom.

I have never tried your idea but understand how to do it. I cound still do it now but dont want to stuff it up. I will leave a bit more material on next time ( no recess inside the foot) and give it a go.

Never stop learning do we but thanks again for all your wise words.

Cheers

G'Day David

Well done and love the wood. Greenie sent!

Cheers
Bernie

stunning bowl dave never had any of that blackwood but now i cant wait to pick some up from someware.

Originally Posted by TTIT

Lovely bit of grain there David and a nice job of presenting it T'is exactly why I always go the crutch!!! - cannot find better figure in a tree.

umong other things

Gotta love that grain. Really well done

Sanding and polishing them edges will make you stutter for awhile, nice bowl and lovley piece of wood grain..LB

Originally Posted by Calm

... I used a HT 1/2 and 3/8 bowl gouges (badly sharpened) and a 1/2 inch round nose scraper. I think the catches were from the grain running in so many different directions ....

Did you try rolling the scraper up at an angle to do a shear scrape?