Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Comments & critique welcome
-
26th May 2013, 06:24 PM #1
Comments & critique welcome
My Woodturning history - got on a lathe about December 2010 after a lesson earlier that year. Had done 2 things at high school I think.
Turned about 150 pens in the first few weeks and a dozen since. Turned a few vases some fruit and 3 or 4 bowls not including this.
This is my first burl and first carving
ImageUploadedByTapatalk1369552763.191838.jpg
ImageUploadedByTapatalk1369552795.590811.jpg
ImageUploadedByTapatalk1369552837.240949.jpg
ImageUploadedByTapatalk1369552871.441047.jpgImageUploadedByTapatalk1369552956.307494.jpgImageUploadedByTapatalk1369553000.924275.jpg
Thoughts for improvement appreciated
Regards
Dave
-
26th May 2013 06:24 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
26th May 2013, 06:32 PM #2
Dave thats a nice burl bowl carving that would have been some hard task.
I do however think its got to much going on with the voids and carving BUT I like it all.
-
26th May 2013, 06:42 PM #3
Nice job overall but IMHO, the finish is too matt/dull and it is a bit on the chunky side for the overall size.
Cheers
DJ
ADMIN
-
26th May 2013, 06:45 PM #4
I find Dave if you keep the edges of your carving/spirals etc sharp it helps to offset all that going on with the burl.
Inspiration exists, but it has to find you working. — Pablo Picasso
-
26th May 2013, 06:54 PM #5
Thx Ray
I might try another coat of Danish Oil and maybe some wipe on poly if I can source some (small country town with no hardware store). Next one I might double quantity of spirals.
Do you mean the valleys?
Thx all
-
26th May 2013, 07:02 PM #6
Nice one dave good thing some nice bloke hooked you up with a power carver
DANGER!!!!I'm Dyslexic Spelling may offend!!!!!
-
26th May 2013, 07:09 PM #7
-
26th May 2013, 08:07 PM #8
[
Do you mean the valleys?Inspiration exists, but it has to find you working. — Pablo Picasso
-
26th May 2013, 08:30 PM #9
-
26th May 2013, 10:13 PM #10
Dunno thats the call of the carver. But I would have thought that using a router would be a challenge of control.
Sometimes I do deep spirals and the last one I posted were relatively shallow. It all has to do with the effect your aiming to produce.
The smaller one has deeper spiralsInspiration exists, but it has to find you working. — Pablo Picasso
-
26th May 2013, 10:56 PM #11
-
28th May 2013, 02:33 AM #12GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
I had some left over satin Poly floor finish that I dipped a rag into and rubbed on the bowl. Two coats gave me a pretty glossy finish.
I use mostly Tung oil for all my finishes. It will make a high gloss on hard wood in a few coats, and eventually on softer woods by applying, let dry overnight, repeat, wet sand with 400 grit and Tung oil, wipe with rag & Tung oil, let dry overnight.
The poly usually does it in two coats.So much timber, so little time.
Paul
-
28th May 2013, 08:51 AM #13
Thx Paul. I need to experiment a lot more with different finishes.
Similar Threads
-
bracing critique
By gratay in forum MUSICAL INSTRUMENTSReplies: 8Last Post: 2nd October 2007, 11:07 PM -
An aid to self-critique
By rsser in forum WOODTURNING - GENERALReplies: 25Last Post: 21st August 2007, 01:12 PM -
critique please
By holzman in forum WOODTURNING - GENERALReplies: 37Last Post: 31st October 2006, 11:55 AM -
A bit of a critique
By Wild Dingo in forum WOODCARVING AND SCULPTUREReplies: 2Last Post: 19th June 2006, 06:44 PM -
Need a bit of helpful critique, please
By Gil Jones in forum WOODTURNING - GENERALReplies: 20Last Post: 27th May 2006, 02:10 PM