Page 2 of 2 FirstFirst 12
Results 16 to 28 of 28
  1. #16
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,792

    Default

    Quote Originally Posted by powderpost View Post
    Point taken Bob, I should have added that there is a wall fan that is set up beside a window, that blows from right to left along the lathe. There is a large double door at to the left of the lathe. Dust, seen or unseen, is not an issue except for any unseen dust that comes in from the outside environment.

    I think that is by far a better arrangement than a dust collector.
    It sounds like your setup is better than most I have seen, but with respect to invisible dust my testing of dust removal by fans that blow has been underwhelming. Its a bit like herding cats and dogs. These fans can work on visible dust but all they seem to do to the invisible dust is rearrange it around the shed.
    It's always better to collect (suck up) the dust at source rather than try to blow it away. The reason most folks have little success with sucking is their DCs and ducting are usuALLY too too small.

    I was visiting a furniture factory just last week that had all their machines attached to several large dust extractors (all using 4" flex) they were still ankle deep in sawdust. They were also using a couple of big fans to blow airborne dust towards two open side doors (on the other side of the shed was a large open roller door) and while the air inside the shed looked clear and there were visible dust streams heading out of the doors, there was still a layer of fine dust over everything. I could see they were using lots of ply and even more MDF - I can smell the invisible dust from those (smells to me a bit like BBQ sauce)- and there was still enough invisible dust present to make me cough. I wish I had brought a particle counter with me.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #17
    Join Date
    Feb 2007
    Location
    blue mountains
    Posts
    4,890

    Default

    Quote Originally Posted by tony_A View Post
    I cant help myself from smiling at visions of this, one if the good things about getting old is not giving a rats @%$! about how you look.

    Perhaps the only good thing. The rest of getting old sucks.
    Regards
    John

  4. #18
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,792

    Default

    Quote Originally Posted by orraloon View Post
    Perhaps the only good thing. The rest of getting old sucks.
    Regards
    John
    SWMBO sleeps well into mid morning if she gets the chance whereas I usually get up around 5am and sometimes times avail myself too he opportunity to go a 24 hour supermarket when there's very few people around. I usually pull on a pair of uggs and jeans and to stay warm pull on a sloppy wind cheater over my fleecy pyjama top. But I have to make sure I change when I get up before SWMBO wakes up - one day about midday she saw me still in this attire and knew I had been to the supermarket. She told me to go look in the mirror. Not only did I still have my pyjama top on it was on inside out.

  5. #19
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    73
    Posts
    11,135

    Default

    Quote Originally Posted by BobL View Post
    SWMBO sleeps well into mid morning if she gets the chance whereas I usually get up around 5am and sometimes times available myself the opportunity to go a 24 hour supermarket when there's very few people around. I usually pull on a pair of uggs and jeans and to stay warm pull on a sloppy wind cheater over my fleecy pyjama top. But I have to make sure I change when I get up before SWMBO wakes up - one day about midday she saw me still in this attire and knew I had been to the supermarket. She told me to go look in the mirror. Not only did I still have my pyjama top on it was on inside out.
    Bob

    Now I have a vision.



    Regards
    Paul
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  6. #20
    Join Date
    Dec 2005
    Location
    Emerald, QLD
    Posts
    4,489

    Default

    Quote Originally Posted by LanceC View Post
    .........Oh, I used to chuckle at turners with their special turning jackets. After standing outside this afternoon striping layer after layer off to try and get rid of chips that found their way through my clothing, I think I will choose something with a tighter neck and arm cuffs next time. I'm sure there will be wood chips on the bathroom floor when I take off my undies this evening.
    Or you can just move to a warmer climate and wear loose fitting singlets (my uniform) so all the chips just fall through to the deck
    .
    Updated 8th of February 2024

  7. #21
    Join Date
    Mar 2008
    Location
    Hobart, Tas
    Posts
    1,211

    Default

    Ttit, but then you have to deal with the electrical hazard of operating power tools whilst standing in a pool of you own sweat [emoji12]. Been there, done that, choose not to any more.

    Back on topic, an attempt was made today at containing the mess. More successful than before, but I think in the long run the answer is going to be to move the lathe into a nook that is naturally contained.


  8. #22
    Join Date
    Nov 2015
    Location
    Whangarei, New Zealand
    Age
    70
    Posts
    282

    Default

    When I still had my old lathe I found that wearing a pair of Yakkas overalls was pretty effective at keeping chips off/out, they are a very dense cotton weave that protect against quite a bit of physical injury as well. Zip it up to the neck, blow the dust and chips off with compressed air when finished, and there was practically no dust and chips tracked into the house.
    I'm contemplating a new lathe, as it were ...

  9. #23
    Join Date
    Jan 2013
    Location
    Tasmaniac
    Posts
    1,470

    Default

    Hi Lance, I wonder if fixing locking castor wheels to the bottom of your lathe stand and moving your lathe outside (weather permitting) through that roller door might be an option to minimise dust build up in your shed.

  10. #24
    Join Date
    Mar 2008
    Location
    Hobart, Tas
    Posts
    1,211

    Default

    Brad, we did consider that, but it would actually be harder to cleanup as all the mess would then be out the front of the house, on grass and rough concrete.

    With the DC sucking from behind the piece, there is surprisingly little dust, just lots of chips. The problem with the current location is that there are simply too many nooks and crannies close by into which chips are thrown in/onto which is awkward to clean up afterwards.

    We actually think we have a workable plan though, which will nesesitate bit of reorganisation in the shed. But in the long run may actually be a better layout.

    Life must be pretty good when these are the thoughts that run through my head at night when I can't sleep, so I'm not complaining.

  11. #25
    Join Date
    Apr 2020
    Location
    Seaford, Vic
    Posts
    397

    Default

    Quote Originally Posted by LanceC View Post
    Thanks all for the responses. I guess the conclusion is that it is all part of the package of turning, and that the best course of action is just to do what I can to make the inevitable cleanup easier.

    My wife and I each turned a coupe off bowls today and made another big mess, but boy was it worth it. So much fun. But we both still managed to get chips all through our clothing. Finding the best clothing is going to be a journey I think. The weather was so warm I had the roller door up today, and I do fear what the neighbors will think if I dressed in Rob's fancy garb.

    Verawood, don't miss out due to fearing the mess. Small spindle turning really doesn't make much mess. Bowls on the other hand, are messy but so much fun.
    I've gone for sandblasters overalls as they seal pretty well around the neck, wrists and ankles.

  12. #26
    Join Date
    Apr 2007
    Location
    Adelaide Hills, South Australia
    Posts
    4,334

    Default

    Quote Originally Posted by RSD View Post
    I've gone for sandblasters overalls as they seal pretty well around the neck, wrists and ankles.
    Scored two pair of RAAF pilot coveralls in my size from an OP Shop years ago, a bit like these...

    British Olive Drab Pilot Overall - Army & Outdoors Australia

    Beneficial features:


    • Zips (not press studs). The main zip on mine goes right up high on neck + Velcro strap to tighten at neck.
    • Also Velcro at wrists to keep out shavings.
    • Plenty of zipped pockets.
    • Pen/pencil sleeves.
    • Zipped side openings to get access to the pockets of clothes underneath.

    Someone told me that they are also flame-proof, but not a feature I've made use of...

    I would never have paid the asking price for these at disposal store back then, but having found how well they have worked since for woodturning I would happily pay the going price now if I ever have to replace them.
    Stay sharp and stay safe!

    Neil



  13. #27
    Join Date
    Dec 2003
    Location
    lower eyre peninsular
    Age
    74
    Posts
    3,582

    Default

    wanted a woodturners jacket from Carbatec, 'out of stock, but search ebay for these'. Fashion Quality Chefs Jacket Washable Kitchen Coat Cook Long Sleeve Coat Uniform

    If you think your medium buy large, fart these chinglese must be small. but finally got one to fit and around the neck its great.
    I would love to grow my own food, but I can not find bacon seeds

  14. #28
    Join Date
    Jun 2004
    Location
    Mareeba Far Nth Qld
    Age
    83
    Posts
    3,070

    Default

    Quote Originally Posted by RSD View Post
    I've gone for sandblasters overalls as they seal pretty well around the neck, wrists and ankles.
    Now that is a good idea, better than "Man's shake", diet for weight loss up here in the tropics!!! Would work better than a sauna.

    Jim
    Sometimes in the daily challenges that life gives us, we miss what is really important...

Page 2 of 2 FirstFirst 12

Similar Threads

  1. connecting without a mess need help
    By drewex in forum WOODWORK - GENERAL
    Replies: 5
    Last Post: 2nd August 2011, 07:49 AM
  2. Ship's Mess
    By Rodgera in forum WOODIES JOKES
    Replies: 3
    Last Post: 2nd January 2010, 06:16 PM
  3. Sticky mess
    By aussieglen in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 0
    Last Post: 30th December 2005, 04:07 PM
  4. What a mess this forum is
    By LineLefty in forum TRITON / GMC
    Replies: 31
    Last Post: 29th October 2005, 09:46 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •