Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Cutting Up A Burl
-
20th September 2013, 11:38 AM #1GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Cutting Up A Burl
I have a Burl about 12 inches X 16 inches that I want to cut to make 2 or 3 pieces for bowls and a platter.
In the diagram the cut face is on the left and the burl grew to the right. Is it better for strength, figure, and any other considerations to cut along the red lines or along the blue lines?So much timber, so little time.
Paul
-
20th September 2013 11:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th September 2013, 12:25 PM #2
I guess it depends on the capability of your equipment. Personally I'd be cutting on the red lines if possible as it looks like it would yield more useable blanks. If cutting on the blue lines you will probably use more wood getting a uniform thickness. This opinion is based purely on the picture. Noting it's a burl, I don't think either cut is going to give more strength due to the irregular grain in burls. You won't know figure until you're inside it as well but again, as it's a burl I don't think either cut will make much of a difference.
It's only a mistake if you don't learn from it.
-
20th September 2013, 12:34 PM #3GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Corbs,
My inclination is to cut on the red lines as it will give me more pieces, and as the section is almost round, less waste.
Equipment will be freshly sharpened chain saw, as I don't have a band saw big enough. I have also used a reciprocating saw (Milwaukee Sawzall) and a pruning blade to get as much as possible, then finished with a bow saw, when I wanted the thinnest saw cut possible
Thanks.So much timber, so little time.
Paul
-
20th September 2013, 12:35 PM #4
If you are sure it is solid, then red would be better, but if there is a chance there is a hollow then blue. Good luck with it, and don't forget photos
Neil____________________________________________Every day presents an opportunity to learn something new
-
20th September 2013, 12:37 PM #5Senior Member
- Join Date
- May 2012
- Location
- Chewton Vic.
- Posts
- 208
Why not do a whole one like I'm going to do with this one Paul?IMG_0239.jpgIMG_0238.jpgIMG_0237.jpg
-
20th September 2013, 02:04 PM #6
I guess it depends what you wan to turn from it. But I would cut along the red first then have look at it and then decide the next step. Its a bit of judgement call either way you go Paul, I'm sure which ever way you go it'll work.
Inspiration exists, but it has to find you working. — Pablo Picasso
-
20th September 2013, 09:22 PM #7Senior Member
- Join Date
- Mar 2003
- Location
- Wauchope NSW
- Age
- 79
- Posts
- 398
Hi paul
Looks more like a cap than a burl the hollow is the remainder of a dead branch, but you will still get some good grain. My suggestion is cut off the right hand side and check for soundness in next layer if the hole is evident cut small blanks around the diameter..
cheers TonyTony
Similar Threads
-
Todays cutting - Blue gum burl
By Stopper in forum SMALL TIMBER MILLINGReplies: 7Last Post: 23rd April 2012, 08:07 PM -
I need help cutting large jarrah burl
By burlboy in forum SMALL TIMBER MILLINGReplies: 9Last Post: 20th October 2011, 04:13 PM -
Help needed cutting burl...
By killerbeast in forum WOODTURNING - GENERALReplies: 9Last Post: 8th April 2008, 08:37 PM -
Cutting Down hill? BURL?
By slopech4 in forum WOODTURNING - GENERALReplies: 1Last Post: 20th January 2008, 10:07 PM