Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Glue Question
-
27th May 2015, 03:10 AM #1GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Glue Question
I have a bunch of 19mm 13 ply plywood that I would like to glue together to make thick enough blocks to use for bowl blanks.
Like so:
https://nanotray.files.wordpress.com...pg?w=300&h=196
And so:
https://s-media-cache-ak0.pinimg.com...c3bf140400.jpg
What sort of glue do you segmented turners use? Use the technical name rather than the brand name as I'm on the other side of the pond - USA.
ThanksSo much timber, so little time.
Paul
-
27th May 2015 03:10 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th May 2015, 08:03 AM #2GOLD MEMBER
- Join Date
- Aug 2012
- Location
- Imbil
- Posts
- 1,167
Hi Paul39,
The photo's look impressive, the glue I use is described by manufacture as polyaliphatic crosslinking PVA hope that helps.
Regards Rod.
-
27th May 2015, 08:21 AM #3
My choice cross-linking polyvinyl acetate for type C & D glue bond ply - Titebond II - same brand on both sides of the Pacific.
It pays to check the glue bond type of the plywood you are using and try to match it for glue performance. Polyurethane may be a better choice for Type A & B bonds.
"Glue BondsThere are four types of glue bond for plywood manufacture described in decreasing order of durability.
Type A – produced from a phenol formaldehyde resin which, sets permanently under controlled heat and pressure. It gives a permanent bond that will not deteriorate in heat or cold or under wet conditions. It is used for marine plywood, structural plywood and exterior plywood which has long term exposure to wet or damp conditions.Type B – produced from melamine fortified urea formaldehyde resin (MUF) which sets under controlled heat and pressure. Type B is suitable for plywood involved in up to two years full exposure to the weather such as in formwork plywood or exterior doorskins.Type C & Type D – produced from urea formaldehyde resin (UF) which sets under controlled heat and pressure. These are interior bonds which are not recommended for any purpose where exterior conditions are involved. Even for interior purposes, C & D should not be recommended for structural applications. For areas around sinks, vanities and laundry tubs, Type A bonded plywood should be used." http://www.awpanels.com.au/plywood/about-plywood/Mobyturns
In An Instant Your Life CanChange Forever
-
27th May 2015, 09:42 AM #4
I do a bit of segmenting and use the type of glue that Rod has referred to. Your equivalent would be Titebond 2. If the plywood is rated for internal use then Titebond 1 would be sufficient, if it is exterior or marine grade then Titebond 2 would be the one to use. In reality, which glue you use will depend on the end use of the bowl, whether it needs a high quality bond or not.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
27th May 2015, 10:30 AM #5GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Thanks to all. I'll put up some photos in due course.
So much timber, so little time.
Paul
-
27th May 2015, 10:37 AM #6SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Normanhurst NSW 2076
- Age
- 81
- Posts
- 484
plywood gluing
Hello Paul 39,
I am not really a segmented turner, so I bow to their advice. However, for gluing plywood pieces for turning bowls , including plywood for pepper mills,
I use Titebond 111 because of its waterproofing ability. It is marketed with green label printing. I also use it for other laminating and find it an excellent product.
Generally, many of us find that the Titebond products are very good. Drillit.
UOTE=Paul39;1868781]I have a bunch of 19mm 13 ply plywood that I would like to glue together to make thick enough blocks to use for bowl blanks.
Like so:
https://nanotray.files.wordpress.com...pg?w=300&h=196
And so:
https://s-media-cache-ak0.pinimg.com...c3bf140400.jpg
What sort of glue do you segmented turners use? Use the technical name rather than the brand name as I'm on the other side of the pond - USA.
Thanks[/QUOTE]
Similar Threads
-
Glue bottle question
By TORB in forum GLUEReplies: 7Last Post: 25th January 2013, 03:02 PM -
glue up question
By coffenup in forum GLUEReplies: 6Last Post: 24th March 2008, 07:47 PM -
glue question
By old_picker in forum GLUEReplies: 12Last Post: 24th September 2005, 10:43 PM -
Glue question
By Soren in forum GLUEReplies: 9Last Post: 25th May 2004, 09:45 PM