Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: GMC lathe tailstock
-
28th April 2015, 11:01 AM #1
GMC lathe tailstock
I recently acquired a GMC lathe as a gift from a bloke who was giving up turning. It seemed like a fair price to give turning a go. I didn't expect much from it, but so far it hasn't been too bad. Its quite good enough to turn tool handles and spindles.
One issue that I have with it is that the tailstock seems to be a dedicated live centre - there is no way I can see to remove the live centre and replace it with, for example, a drill chuck so that it can be used to drill holes in items held in a chuck at the headstock.
Nothing in the Manual that came with it mentions replacing the tailstock, so I assume that this is just another limitation of the machine. I suppose I could just build a new tailstock from hard wood and fix a suitable Morse taper into it, but I thought I would just check with those who know better before embarking on that exercise.Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
28th April 2015 11:01 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
28th April 2015, 12:17 PM #2GOLD MEMBER
- Join Date
- Jan 2010
- Location
- Melbourne
- Posts
- 2,636
Is there a 'hole', about 25mm diam at the back of the tailstock? If so, you could push out the live centre with a rod down the tailstock. If not, then I'm 'clueless'!
-Scott
-
28th April 2015, 06:13 PM #3Senior Member
- Join Date
- Aug 2012
- Location
- Banora point,NSW.
- Posts
- 172
Gmc Lathe
Any chance of a photo of the lathe and tail stock ?
Cam
-
28th April 2015, 08:04 PM #4
If its one of these http://www.dealsdirect.com.au/gmc-1-2hp-wood-lathe/ I doubt you will have many options.
Mobyturns
In An Instant Your Life CanChange Forever
-
28th April 2015, 08:50 PM #5GOLD MEMBER
- Join Date
- Jan 2013
- Location
- Tasmaniac
- Posts
- 1,470
GMC? Eh?
-
29th April 2015, 12:32 AM #6Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
According to an Online tool review ,made when this machine was sold, this machine doesn't have a headstock or tailstock with morse tapers.
Peter.
-
29th April 2015, 04:27 PM #7
-
29th April 2015, 05:32 PM #8Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
-
30th April 2015, 03:03 AM #9GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Jeremy,
I would use the lathe as is until you decide you are not going to do much turning or the hook is set deeply enough that you will want a real cast iron bed lathe.
I have two of these, one free and the other $10. They are worth what I paid for them. I have a couple of big heavy real lathes that I use.
The lightly built square or round tube bed lathes tend to flex and the tool rest and tail stock move in different directions, which makes for difficulty in doing good work.
The lathe will probably do good tool handles and not too long spindles.
The bed can be stabilized buy making a block of wood to fit snugly between the bottom of the bed and the bench, and making a block to fit over the tubes with a hole to screw the top block to the bench.So much timber, so little time.
Paul
-
30th April 2015, 08:37 AM #10
Anything for free is a good choice. Do show some of the items that you have turned.
Sorry not familiar with the product and only guessing the next part, but was wondering if it can be taken apart from the tail stock? That's what I had to do with my first lathe remove the part that held the live centre and used a metal rod to remove.
-
30th April 2015, 11:02 AM #11New Member
- Join Date
- May 2012
- Location
- Adelaide
- Posts
- 6
I have one of these lathes and I'm afraid we are stuck with the existing tail stock.
To drill a hole in a piece, I put the bit in a drill and using the tool rest for support, feed it in ever so slowly.
Make a center hole in your work first, otherwise the bit will not centre and you'll end up with a broken bit, or ruined workpiece.
Sorry !
-
30th April 2015, 02:58 PM #12
Depends on what you wish to drill holes into, if its blanks for tool handles, you may be able to secure the drill bit in the head stock end with the supplied chuck. Mark centers on each end then place one end into the live center and make a jig to elevate the head stock end of the blank up to center height and to secure the blank against possible rotation. then use the tail stock to advance the blank onto the drill bit. I believe Ken Wraight published an article not long back on a similar method in either Australian Woodworker or Wood Review.
CAUTION - this technique is only suitable for small hole diameters.Mobyturns
In An Instant Your Life CanChange Forever
-
30th April 2015, 04:17 PM #13
Thanks for the replies.
Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
Similar Threads
-
Lathe tailstock repair (retapping grub screw)
By HSS in forum METALWORK FORUMReplies: 2Last Post: 12th September 2012, 06:11 PM -
jet min lathe tailstock problems
By woodwormer in forum WOODTURNING - GENERALReplies: 7Last Post: 19th January 2012, 01:39 AM -
Lathe headstock and tailstock are out of alignment
By 19brendan81 in forum METALWORK FORUMReplies: 24Last Post: 22nd November 2010, 03:00 PM -
Lathe Tailstock
By zeddy19 in forum WOODTURNING - GENERALReplies: 7Last Post: 19th June 2009, 09:19 PM