Thanks Thanks:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 4 of 4
  1. #1
    Join Date
    May 2019

    Default Help with dust collector & remote pls

    I have a JetMac 2hp dust collector with either a nvr or magnetic switch. I bought a remote control socket receiver and remote control. Bascially plug DC in and turn it on and off. Bit the current setup is that Everytime the machine powers off I cannot turn back on with remote. I had an electrician rewire it to a normal on/off tool switxh but her never did anything like that and it worked but after about 20 minutes motor failed. Jetmac replaced entire motor and switch. I would like to know if there is a way I can do this. My remote can power three items and I want to hook the 2hp Dc, and my in shop wet/dry vac to it. I have photos of what I am talking about and the switches and remote etc but do not know how to post them on here.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Advertising world

  3. #2
    Join Date
    Oct 2019
    Adelaide, South Australia


    I bought a 2 hp Carbatec dust collector with a NVR switch and I already had a set of remote sockets. The only way around it is to pull the switch apart and basically join the Positive wire from the power lead to the Positive wire from the motor, and then the same with the neutral wires this will give you a permanent "ON" situation, so when you switch of the power point with the remote, the dust collector shuts down until you "fire" up the power point again with the remote. I am not an electrician but this was told to me how to do this and it works a treat, has done for over a year now.

  4. #3
    Join Date
    Oct 2007
    Alexandra Vic


    For the original poster, NVR switches and magnetic switches are one and the same. Basically the Start switch engages a high power relay, which has multiple contact sets. One or two sets of contacts control the motor, depending on whether it is configured as single pole switching, or double pole switching. An additional auxiliary set of contacts keeps the relay energised when you release the Start switch, until either the supply power to the system is removed or you press the Stop button. The Stop button breaks the auxiliary relay contact circuit when pressed, causing the relay to de-energise and break the main contacts controlling the motor.

    If you fit a remote between the wall socket and the switch on the DC, switching off via the remote is equivalent to a power failure or unplugging at the wall socket, and the DC will not run until you activate it at both the remote and at the DC power switch. This seems to be what you have described in the first part of your message, suggesting that the original switch is in fact an NVR or magnetic switch. It is quite common to have these units installed in machinery without knowing it or without it very obvious. About the only only machinery switches that don't work on that principle are ones that are obviously a toggle style switch with mechanical latching. Anything with a momentary Start push button will use some form of electronic/magnetic latching and operate as an NVR style switch.

    IF you wish to operate a device with NVR switching, you have two basic option, bypass the NVR switch and go without the benefits it provides, (mainly ensuring that after a power failure the unit does not start automatically when power is restored, but needs a human command (pushing the Start button) to restart), or alternatively the remote system needs to be installed between the NVR and the motor. This approach can be more difficult to accomplish, but retains the auto start protection offered by the NVR system.

    My reading of the modification of the switching followed by early motor failure suggests that the person doing this task may have included/excluded some cables to the motor, leaving a run capacitor out of circuit or leaving the start winding of the motor in circuit permanently, both of which will cause excess current draw by the motor and winding damage leading to failure.

    Fundamentally, the description given by fof47 is correct except that with AC systems the voltage changes from positive to negative then back to positive 50 times a second in Australia or 60 times a second on USA. Hence the terms Positive and Negative are meaningless, and the term Active or Line is used to denote the higher potential leg of the supply, and Neutral is used to denote the leg that is at or very near earth potential.
    I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.

  5. #4
    Join Date
    Oct 2009
    South Africa


    Quote Originally Posted by malb View Post
    IF you wish to operate a device with NVR switching, you have two basic option, bypass the NVR switch and go without the benefits it provides, (mainly ensuring that after a power failure the unit does not start automatically when power is restored, but needs a human command (pushing the Start button) to restart)
    Some remote switches (possibly even most) will act as a NVR switch too, as they default to open when powered up.

Similar Threads

  1. Remote control on DC-7 dust extractor.
    By DaveVman in forum DUST EXTRACTION
    Replies: 26
    Last Post: 23rd Jan 2019, 02:11 PM
  2. Carbatec Dust Collector - Switch Change for Remote
    By pach in forum DUST EXTRACTION
    Replies: 11
    Last Post: 8th Apr 2018, 10:30 PM
  3. All in one workbench / dust separator / dust collector
    By HeadScratcher in forum DUST EXTRACTION
    Replies: 15
    Last Post: 9th Jul 2012, 12:25 AM
  4. Replies: 3
    Last Post: 7th May 2012, 08:34 AM
  5. Dust Extractor: Remote Control
    By Groggy in forum HAND TOOLS - POWERED
    Replies: 13
    Last Post: 8th Jul 2009, 05:23 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts