Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
9th December 2006, 02:46 PM #1
Help with using a turning tool shaped like a disk
A few years ago I purchased a turning tool that was a solid steel handle (lead shot inside the grip) It used one of two slide in attachments that held the cutting tool. One was a disc shaped cutter the other a piece of HSS 6x6x35 with a square end and a rounded end
anyway
I have never been able to use either as I recieved No instructions on their use and can't find any suitable web based tutorials either..
I got the thing after I saw it demo'd at the Brisbane WWW show, the demonstrator was turning beautiful long shavings off a blank and getting a lovely smooth finish similar to a skew. I can only get it to scrape its very frustrating not to mention I paid 195 dola for the three objects. ( Handle and two plugins).
Has anyone ever used one?
Anyone know how to present it to the wood and (also) sharpen it.
Do you know the sort of tool I mean?
-
9th December 2006 02:46 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th December 2006, 04:28 PM #2
Aye, Amarks. I think...Perhaps...Maybe. ) Turn the scraper at about this / angle, slightly above center, and take very light cuts. Test it out on scrap timber.
Go to http://www.aroundthewoods.com and check out his "Make a Tool". Lot's of good stuff there about the other cutter.Al
Some minds are like concrete thoroughly mixed up and permanently set.
-
9th December 2006, 05:11 PM #3
I assume from you description that it is a Vermec hollowing tool.
http://cws.au.com/cgi/index.cgi/shop..._id=1107370071
The 6mm sq peice is for your initial hollowing and the round disc is for your shear scraping.
Have your toolrest set above centre height and with the nose of the tool down and on about a 30 degree angle hollow out the centre of your bowl. Use the scraper disc on about a 45 degree angle.
Use your arm to support the tool and you will get better control.
Get yourself some green timber to practice with as it is a lot more forgiving. If you use dry wood and have a catch you can get into all sorts of bother. I find this tool works great on open forms where you can see the tool and make any adjustments to the angles but I prefer the munro holowing tools for closed forms.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
9th December 2006, 05:16 PM #4
Concise and to the point, Jim.
I'll second the green wood and open form bit, too. Can't comment on the Munro as I don't have one.... yet.
- Andy Mc
Similar Threads
-
Where do you point your tool?
By Phil Spencer in forum WOODTURNING - GENERALReplies: 13Last Post: 17th October 2006, 11:12 PM -
Tool Addiction
By Ian007 in forum WOODWORK - GENERALReplies: 108Last Post: 30th June 2006, 08:44 PM -
Tool Envy Syndrome
By Bodgy in forum HAND TOOLS - POWEREDReplies: 4Last Post: 12th August 2005, 12:17 AM -
Suggestions for using rotary hi-speed tool
By Bob H in forum INTARSIAReplies: 1Last Post: 24th November 2004, 10:00 AM -
Gouge tool for bowl turning
By G00se in forum WOODTURNING - GENERALReplies: 10Last Post: 21st July 2003, 08:53 PM