Needs Pictures: 0
Results 1 to 15 of 16
Thread: Home made tool shafts
-
24th May 2015, 09:24 PM #1
Home made tool shafts
For those that have made their own turning tools (carbide or otherwise - not scrapers) Do you have a preference for square, round or hex bar stock?
I have made a few with square stock but wondered if round or hex would be preferable.
Thanks
Phil
-
24th May 2015 09:24 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th May 2015, 09:43 PM #2
Hi Phil, I have made quite a few tools from mild steel flats. These have pieces of heavy machine hack saw blade silver soldered to the top to make cutting edges. They have all been made for special jobs. This suits me as I cannot slip around the corner to the tool shop, the nearest turning tool shop is more than a days drive from here. My regular turning tools are mostly factory made tools bought on mail order.
I have "converted" axes, motor car engine push rods and welders chipping hammers, mostly for fun. Chinese high speed blanks are now available here in Australia, that is another source of HSS material. Round or square would depend on what tool is required.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
24th May 2015, 10:01 PM #3
Thanks Jim,
Useful info. Not quite as isolated as you but still have to travel a distance to get anything.
Sorry but I think on rereading my post I did not ask the right question.
What I wanted to know was: If I made a carbide or oland type tool which type of shank would you prefer square, round or hex?
Square is limited in how the tool is angled to the work.
Round is infinitely variable.
Hex has a few angles to choose from.
Which would you prefer?
Hope this makes a bit more sense now.
Phil
-
24th May 2015, 11:23 PM #4Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Phil,
I made a set of Oland type of tools and I used round pieces of old gal waterpipes. Sanded them smooth and clean on the lathe between centres with sand paper and screwed, and glued with epoxy,into the pipe a threaded rod which goes at least 150 mm into the handle for strength and rigidity.
They weigh a lot but are very easy to use.
Peter.
-
25th May 2015, 09:43 AM #5GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
My preferences for tools that are rotated is round. As for shear scraping. For scrapers flat bar. For Bedan type tools square. I have eased the edges on my skews so they don't nick the tool rest when I have the skew up on the edge.
These folks make a skew any way you would like:
http://www.hamletcrafttools.co.uk/skew-chisel.html
I don't think there is a right or wrong shape, whatever you prefer.
I have found a free source of round bar by dismantling scrapped copy machines and printers. They are ground and chrome plated, from 1/4 to 5/8 inch in diameter.So much timber, so little time.
Paul
-
25th May 2015, 11:08 AM #6SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Normanhurst NSW 2076
- Age
- 81
- Posts
- 484
-
26th May 2015, 10:38 PM #7
Phill I make around 50% of my own tools and use squared, hex and round depending on what I want it for. Its a bit of a personal choice and what steel you have to hand probably adds to it as well.
Inspiration exists, but it has to find you working. — Pablo Picasso
-
27th May 2015, 09:00 PM #8
Thanks all for the replies.
As was said a few times - it depends on your preference.
So it is time to try each. Going to start with the round as more easily available in the area.
Will see how it goes, will definitely be cheaper than imported tools.
Thanks
Phil
-
28th May 2015, 04:58 AM #9SENIOR MEMBER
- Join Date
- Oct 2009
- Location
- South Africa
- Posts
- 950
Braziers in Pietermaritzburg have some fairly cheap high speed steel pieces, next time you're in town. I just wish they were open on Saturday, I never seem to get in there during the week.
-
28th May 2015, 09:55 PM #10
Phil I use round for Oland type tools, it just easier to roll the tool over with a round bar.
Inspiration exists, but it has to find you working. — Pablo Picasso
-
29th May 2015, 10:02 PM #11
-
30th May 2015, 11:01 AM #12GOLD MEMBER
- Join Date
- Jun 2010
- Location
- shoalhaven n.s.w
- Posts
- 1,240
One thing with square and rectangle bars is you have more surface area of tool on the tool rest but harder to manipulate angle of cutting edge.
I have been experimenting with the round bright bar. And have shelved it for the moment.
i would be interested in how the hex bar might go, could be onto something!Turning round since 1992
-
31st May 2015, 10:52 PM #13
Got some 10mm, 12mm and 14mm round, square and hex.
When time permits will make one type in round, square and hex and try them out.
Will come back with my feelings when I have done the first set.
Phil
-
14th April 2016, 02:19 AM #14
Nearly a year but do have some feelings after some trial and error.
Not everyone will agree but I find the hex bar to my liking.
Easy to set and keep an angle and this is great in a deepish pot/bowl.
The round bar twisted and made control difficult.
The square bar is difficult to hold for a shear cut .
So in my opinion 14mm hex is the one.
I am sure there will be other opinions but these are mine.
Cheers
Phil
-
14th April 2016, 05:14 PM #15
After reading your post I guess what I am thinking a photo might be necessary.
Similar Threads
-
Home made Fullering Tool
By BobL in forum THE SMITHYReplies: 8Last Post: 7th August 2013, 06:05 PM -
home made hollowing tool
By thefixer in forum WOODTURNING - GENERALReplies: 4Last Post: 27th March 2008, 06:30 AM -
Home-Made Tool
By Fredo in forum WOODTURNING - GENERALReplies: 12Last Post: 7th August 2007, 12:49 AM -
Home made parting tool
By Tiger in forum WOODTURNING - GENERALReplies: 29Last Post: 26th May 2006, 04:26 PM