Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: indexing a wood lathe
-
31st March 2013, 08:45 AM #1Senior Member
- Join Date
- Jul 2012
- Location
- Minnesota USA
- Age
- 64
- Posts
- 150
indexing a wood lathe
I have seen the typical set ups for index pins and presets. Any other ideas for indexing? something that allows easy set up and more possibilities? I have thought about a degree wheel of about 8-10 inches in diameter but thin like 10 gage steel. This would allow individual marks to be far enough apart to see and possibly a vernier scale to get fractions of a degree. In stead of using a pin and having to make a hole that takes room, use a clamp or brake that once lined up could be locked down while a required operation was performed. I am looking for suggestions or ideas to ad one on my homemade lathe.
-
31st March 2013 08:45 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
31st March 2013, 09:00 AM #2
Sounds good idea a heavy magentic break might be the go.
I have an alli one with holes for a pin.
-
31st March 2013, 09:26 AM #3
Do you mind if I pull up a chair next to you to see how the collective grey cells will answer your very good question? I made up a ¼" (6mm) flat wheel with 24 holes and a pin that screws into the hole. Yes it works but even selection 8 holes out of 24 kept me checking and rechecking as I made some flats with the router. I was making a sample chisel handle aka English design. I intend to make handles for the HSS chisel set coming from Thumbsucker.
When I look at the hole sets on a dividing head it makes me very envious but how do you decipher which set of holes to do what?Just do it!
Kind regards Rod
-
31st March 2013, 11:16 AM #4
I've made one out of wood segments then covered with Aluminium Sheet.
Here a link to the Video, it's in Italian but easy to follow. it as 3 rings with different Holes 32-33and 48.
Indicizzatore - YouTube
Cheers Tony.
And a photo of it at work.
Open Segment 2013 (8).jpg
-
31st March 2013, 12:25 PM #5Senior Member
- Join Date
- Jul 2012
- Location
- Minnesota USA
- Age
- 64
- Posts
- 150
Nice Tony thanks for the pic. I cant view vids atr work but i will check it out when I get home in the AM.
I am going to horse around with some designs tonight if time permits. I purchased a disc brake calliper for a go cart. there is a small (.005) bit of play in the guide shafts but if it is locking down on a 10" dia wheel It would be negligable for most applications. I think I can take the play out if I am a little creative.
I would like to attatche it to the spindle in my case in the middle. The drive is at the rear outboard and I have other things i want to do off the nose area. I will scribe the degree marks in typical fashion: 10 degree increment lines the longest and include numerals. Divisions for five degrees shorter and the last 1 degree increments the shortest. I will place an indicator peice just inside or outside of the marks so that they can be read as a vernier and include marks for 0,1/4,1/3,1/2 2/3 and 3/4 degrees to line up with. I may use a peice of plexi for this and look through it. when the degree is where I want it I will lock down the caliper and perform the operation. That is my take on it mabe over kill but unlimited. Still looking for other input.
-
31st March 2013, 02:24 PM #6
This is the indexing head I used for cutting teeth on clock wheels and also for wheel making. I have made several discs that go on the back of the Vicmark chuck. I took the cover off the back of the chuck drilled 2 holes and tapped 1/4in threads to hold the discs. Any combination of pattern can be used. The back of the wheels are numbered , the adjustment is by the spring loaded clip at the back.
The base the drill is fixed too has a sliding unit which can be positioned at any angle, will also take a router. John.
-
31st March 2013, 07:12 PM #7
hi guys,
another idea is a robert sorby indexing system ,i had one on
my old lathe and it worked very well,it seemed to get in the
way on the chuck side so i made a hand wheel and attached
the indexer to that,it has a adjustable ''pin'' which swivels in and out
hope this helps
cheers smiife
-
5th April 2013, 12:02 PM #8Senior Member
- Join Date
- Jul 2012
- Location
- Minnesota USA
- Age
- 64
- Posts
- 150
P82A0049.jpg
Here is one of two index rings I have been working on. This one uses a disc brake froma a go cart and a homade index wheel. I had to grind out about .030 from each side to get it to fit. the other hweel is two piece and mounts outboard of the rear of the headstock. A rosette attatches to it and it will phase the rosette with the spindle.
-
8th April 2013, 12:01 PM #9Senior Member
- Join Date
- Jul 2012
- Location
- Minnesota USA
- Age
- 64
- Posts
- 150
P82A0055.jpg
Here is a picture of the outboard end of the phasing index ring. the four bolt holes provide a means of attaching a rosette to the ring.the ring with the window in it here is attatched to the ring with the four bolt holes. This assembly turns freely on the hub untill locked in place. the center hub attaches to the spindle.
P82A0056.jpg
here is the reverse side of the first picture it also has a window and index markings.
P82A0057.jpg
here you can better see the window and markings 360 marks.
P82A0058.jpg
here is the assembly mounted on the lathe the large sprocket cam be removed but even at 2700 rpm has caused no vibration issues.
P82A0059.jpg
lastly a side view of the assembly. In this way I can Phase the rosette to the spindle for rose engine work. the picture shows the drive in 350-2700 set up. with the jackshaft i can get down to 35 rpm and for rose engine a dc gearbox drive will drive the sprocket down to 3 rpm.
Similar Threads
-
NOVA DVR XP Lathe Indexing Problem
By bdfairlie in forum WOODTURNING - GENERALReplies: 2Last Post: 22nd August 2012, 09:13 PM -
More Indexing in the Lathe
By Abratool in forum METALWORK FORUMReplies: 8Last Post: 21st July 2012, 10:07 AM -
the making of an indexing system for the mini wood lathe
By harrysin in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 7Last Post: 17th January 2012, 12:20 AM -
HEADS UP Wood lathe:jet 1220 midi lathe
By Woodwarehouse in forum ANNOUNCEMENTSReplies: 0Last Post: 1st December 2011, 03:02 PM -
Converting a Metalworking Lathe to Wood Turning Lathe
By GrinlingGibbons in forum WOODTURNING - GENERALReplies: 13Last Post: 29th March 2011, 07:17 AM