Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Longworth Chuck
-
5th May 2014, 06:13 PM #1Member
- Join Date
- Apr 2010
- Location
- clayton
- Posts
- 58
Longworth Chuck
Hi team, I had been having a couple of slight problems with my Longworth chuck, It was not sliding properly for one, no bigee just pull apart and clean being careful not to put more dust behind the centre "slip disc" than I removed. The second problem was a vertical split the full length of one rubber "gripper". So a trip to Clark Rubber to purchase 8 no7 rubber stopers ($10.40). In an offcut turn a tapered hole to fit same stoppers, drill bolt hole through stopper, slightly oversize ( rubber doesn't cut clean) and at 2000 revs? (faster could be better) and reassemble. Voila as good as new----- maybe. Jay
-
5th May 2014 06:13 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th May 2014, 12:04 PM #2
Any photos?
-
6th May 2014, 06:09 PM #3Member
- Join Date
- Apr 2010
- Location
- clayton
- Posts
- 58
Photos?
Hi Christos, thanks for the question; but no photos. It looks the same as a new one plus a bit of wear and tear. I was just letting everyone know where to get replacement grippers? the name number and cost. The cleaning bit was easy to work out, as was the tapered recess to grip the rubber stopper. drilling the hole depends on drill bit type and sharpness, take it slow drill slightly oversize at 2000 revs was my best result. Jay
-
9th May 2014, 12:13 AM #4New Member
- Join Date
- Feb 2013
- Posts
- 4
I had the same problem with mine. Cleaned it and ordered new bumpers through Amazon. They are not rubber like the originals. They are synthetic, and should not dry and crack like the rubber ones.
-
9th May 2014, 09:13 AM #5Senior Member
- Join Date
- Aug 2012
- Location
- Banora point,NSW.
- Posts
- 172
Rubber tip!
I have found previously when cutting rubber it cuts very cleanly when its been in the freezer for a couple of hours, may be the same when turning ?
Cam
-
9th May 2014, 01:45 PM #6
I use rubber walking stick ends and fill em with a wooden dowel
Inspiration exists, but it has to find you working. — Pablo Picasso
-
10th May 2014, 10:10 PM #7GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Townsville. Tropical Nth Qld.
- Posts
- 1,244
Jay if you do a google seach, you can get the flask stoppers pre drilled to take glass tubes for science experiments.
Rgds,
Crocy.
-
10th May 2014, 10:10 PM #8GOLD MEMBER
- Join Date
- Jun 2010
- Location
- shoalhaven n.s.w
- Posts
- 1,240
Hi all! Another option which I used was the bushes from skateboard trucks! Not overly thick but seem to be working well for me!
-
11th May 2014, 08:17 AM #9
Freeze the rubber stoppers then drill or as me ole mate Croc says use "flask stoppers."
ps hope you are only drilling the stoppers at 2000 rpm & not spinning the longworth at those rpm .
Similar Threads
-
Longworth Chuck
By Skewturn in forum WOODTURNING - GENERALReplies: 2Last Post: 8th April 2012, 11:22 PM -
Longworth chuck
By Chumley in forum WOODTURNING - GENERALReplies: 26Last Post: 4th June 2009, 04:47 PM -
Longworth chuck
By Keoni in forum WOODTURNING - GENERALReplies: 8Last Post: 7th May 2008, 10:42 PM -
Longworth chuck Mk1
By orraloon in forum WOODTURNING - GENERALReplies: 11Last Post: 21st November 2007, 11:37 PM -
longworth chuck in polycarbonate
By hughie in forum WOODTURNING - GENERALReplies: 5Last Post: 15th August 2007, 08:07 PM