Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
-
11th May 2014, 12:30 PM #1New Member
- Join Date
- May 2014
- Location
- Australia
- Posts
- 3
(Newbie) question on head stock mountings
Hi to all , first post here and rather new at turning. I have been playing with my old new toy (wood lathe) for a few weeks and really enjoying it.
been turning a few bits of oregon and pine and some vic ash, just spindle work with the tail stock supporting.As i have only one small central screw faceplate,I am noticing that the timbers (all the above) are destroying the thread inside the timber on the head stock side after a while to the point where the timber is stalling.
I have a 1 inch spindle with 8 tpi thread just wondering what im doing wrong and if there are any cheap second hand faceplates and or chucks around i can purchase. Most of all some advise please
-
11th May 2014 12:30 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th May 2014, 05:05 PM #2GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
What you are using on your headstock, is a screw chuck and is normaly used in crossgrain for example the top side of a bowl blank while you are shaping the outside and bottom of it.The way you are using ,it in end grain, it will invariably chew out the hole.I asume you can remove this screw chuck and will have a hollow shaft with a M2 taper in it.In this you mount a spur drive which will fit in a centre punched hole in your bit of wood and away you go.Spur drives are not expensive .
Ted
-
11th May 2014, 07:22 PM #3
Hi one good turn and welcome to turning and this forum,
As Ted pointed out that is a screw chuck and is usefull for some small faceplate work. You need a spur drive. Is there any other bits and pieces came with that lathe. If so post some pics and the good people on here will point you in the right directon. A spur drive is not expensive and thread adaptors can also be obtained to fit chucks and the like.
Regards
John
-
12th May 2014, 05:46 PM #4Senior Member
- Join Date
- Aug 2012
- Location
- Banora point,NSW.
- Posts
- 172
Spur drive
Mate, its worth putting your location a lot more specifically, you will find most folks on here incredibly helpful and don't be surprised if a local turner drops one off in your letterbox !!
Regards and welcome,
Cam
-
12th May 2014, 11:30 PM #5
One Good Turn; Welcome to the forum and to wood turning.
As others have said a spur drive would be better for spindle turning.
-
13th May 2014, 07:26 AM #6New Member
- Join Date
- May 2014
- Location
- Australia
- Posts
- 3
Ok thankyou turnerted, orraloon,tangoman,christos thanks guys for that information on spur drives and also i never realized the middle of screw chuck was changeable, but as pointed out will help me work out a few possibilities.
For any interested i live in Anglesea victoria ,carnt seem to update profile so sorry im from australia at the moment.
Would i be right to assume there are different sized spur drives for different sized timbers, I eventually would like to turn some table legs and the like when more experienced , im very interested in some barley sugar twists and the like, and realize these cannot be turned ,but i have seen some router assemblies geared to a lathe for this purpose.
Also if i want to turn larger ,heavier timbers (200-300 mm)logs,do i need to upgrade head stock/tailstock fittings ?
-
14th May 2014, 11:19 AM #7
I love to hear from a man with ambition
I think the best advice anyone can give you is to find your local wood turning group and go along you will be amazed at the amount of help and knowledge that they will be only to willing to give and it is so much easier to learn when you can see what is going on right in front of you
Ohh and welcome to the slippery downhill slide of woodturning
regards
Bowl-BasherI can turn large lumps of wood into very small bowls
-
14th May 2014, 02:29 PM #8
Welcome to the forum OGT. As Bowl Basher suggested, coming to a club is a good place to start when you are learning what to do. You can get some information about my club from the link on my signature. You probably can't edit your location until you get a certain number of posts up (not sure what that No. is).
When you unscrew the screw chuck from the headstock shaft, is there a morse taper (tapered hole) in the headstock shaft. Some cheaper lathes don't have them which makes life a little more difficult, but it's not the end of the world and can be worked around.
Does it have a brand name?Dallas
-
31st May 2014, 05:30 PM #9New Member
- Join Date
- May 2014
- Location
- Australia
- Posts
- 3
Thanks Treecycle ,just had a play with the screw chuck and have found that it is also threaded into the screw chuck , so mine must be a cheaper model i guess,bugger coz ive purchased the wrong type of spur drive,anyway i guess ill have to look for the threaded type or a fitting of some description
-
31st May 2014, 06:41 PM #10Retired
- Join Date
- May 2012
- Location
- Canberra
- Posts
- 1,820
OGT, definitely post a bunch of pictures. The number of people who have truly arcane knowledge here is unreal.
Pix of the headstock, back, guts and any branding.
They will have you sorted quick smart.
LOTS of pictures of your work too....they will offer pointers.
-
31st May 2014, 09:09 PM #11Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Lots of good advice here OGT!! Take note!! Welcome to the addiction!!!
-
31st May 2014, 09:12 PM #12Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Bowl Basher!! Where have you been??
I've missed you!!!
-
31st May 2014, 09:47 PM #13Senior Member
- Join Date
- Dec 2008
- Location
- 75 km north of newcastle
- Age
- 76
- Posts
- 110
The screw chuck has hole/s for a tommy bar on it's outer rim. Is there a spindle lock or hole in the spindle or flats that you can use to hold the spindle and allow you to unscrew the screw chuck form the spindle. it looks from the photos as though the spindle is big enough to have a M2 taper inside. The lathe also appears to have an outrigger on the outboard side - is there a hole through the spindle visible from the rear?
Mick Cmañana
-
2nd June 2014, 08:02 AM #14Member
- Join Date
- Jan 2009
- Location
- Pluto
- Posts
- 72
I agree with Mick looking at the photos.
Here is a link to holding methods by Mike Peace and he covers almost all methods of holding a piece on the lathe in the 1.5 hours.
http://www.youtube.com/watch?v=aUXil-5dEeo
Similar Threads
-
Head Stock Spindles
By Skewpid in forum WOODTURNING - GENERALReplies: 15Last Post: 12th November 2006, 12:24 AM -
mc1100/900 head stock wobbles
By hughie in forum WOODTURNING - GENERALReplies: 5Last Post: 27th April 2006, 03:59 PM -
Head Stock & Tail Stock extention plates
By Babytoolman in forum WOODTURNING - GENERALReplies: 0Last Post: 25th December 2005, 11:37 AM -
MC900, Head Stock
By Bruce Micheal in forum WOODTURNING - GENERALReplies: 12Last Post: 15th February 2005, 10:39 AM