Thread: Noise from headstock

Any other tools nearby - such as a gouge rocking back and forth.

check the set screws on your pulleys, one of them could have backed off and slow speed its causing the click,
at high speed the centrifical force keeps it from clicking.
had it happen on my pm3520

IAN

Originally Posted by ihmserv

check the set screws on your pulleys, one of them could have backed off and slow speed its causing the click,
at high speed the centrifical force keeps it from clicking.
had it happen on my pm3520
IAN

had that once too. Shows you don't learn from experience

Ian, thanks; could be a good call. Will get out the manual to see if set screws are used or a key.

Jim ...

Paying careful attention here as the problem-solving guru has weighed in

Tools are down lower on the right side on rubber mat and shavings - but the right ear is not that hot. Left ear is better and is on the headstock side. Could have been reflected noise.

Have just tried spinning the lathe with a block of MDF pressed against the spindle. No noise but it wasn't that quiet an operation.

Can't hear it spinning the spindle by hand. Pushing and pulling on the handwheel shows up nothing but there's prob. only a poofteenth in it.

Maybe it was the bowl.

Heading back to the shed .... may be some time.

K. It uses a key to drive the pulley and setscrew to align it. Screw was tight. All other setscrews ditto.

May also have been the 'new' Longworth chuck - its first outing.

Ern,

If you do not have a mechanics stethoscope, get a screwdriver or dowel 12ish mm in diameter about a foot long and put the handle end up to your ear and touch various points on the headstock while running or turning by hand.

You will hear all manner of interesting noises, maybe even from where the click is emanating.

Originally Posted by rsser

Heading back to the shed .... may be some time.

Now where have I heard that before?

One of my chucks makes a similar noise under about 600rpm - turned out to be the tightening-hex-socket wobbling in it's recess.
Another one that had me looking around for a while was a thin shred of rubber hanging off the drive belt that was flicking against the housing.
The options are almost endless Have fun Ern

Thanks Vern. It was my oldest proper chuck, a very well-used VM100.

The belt's looking good.

The noise is only happening under load. Slight load at that.

Paul, good thinking. Yeah I have a scope but to load and listen am one hand short. The missus was thoughtless enough to be working late today.

Can't backtrack to remount the bowl cos those bleeding Longworth chucks allow you to skim the foot. Knew it was a bad idea to depart from recess mounting

Jim, I may be some *more* time. Will take the emergency beacon into the shed this time

K, best I could backtrack was to mount the bowl in the Longworth chuck with the old VM100, and put some pressure twds the headstock.

Don't like standing in the line of fire of a new mounting device but needs must (musted?) to listen to the stethoscope. Fascinating to hear a change in pitch at the outboard bearing with such slight loading ... but no chicking.

This is shaping up to be the Chinaman's horse in the old tale.

Thanks all for your suggestions.
.

I had a PM3520A and it started doing that. I traced it to a burr on the spindle lock. There were only 2 positions then, and a heavy 1/2 inch or so thick pin that went into a slow. Filed off the burr, and no more problems.

robo hippy

Thanks rh. Will take a look.

But tricky to diagnose via email But if you have a face plate use that to try and get the clicking going on the lathe that will eliminate all the chucks etc if its the bearings.As for belts clicking etc change tension on your belts, generally back it off some. Other wise its just a process of elimination over time,slow and annoying.

There dosnt happen to be a hard piece in your buffing rag or a small crack in the bowl

Regards Ian T