Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 23 of 23
Thread: Outboard/left hand turning
-
17th March 2013, 12:11 AM #16
No.4 MT ???.
Hi Michael,
Beats me why there wood be a 4MT On a Lathe with such a Spindly Bed.
Must Bounce like mad at times.Regards,
issatree.
Have Lathe, Wood Travel.
-
17th March 2013 12:11 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
17th March 2013, 06:32 PM #17Senior Member
- Join Date
- Mar 2011
- Location
- New Zealand
- Posts
- 186
-
17th March 2013, 07:12 PM #18Senior Member
- Join Date
- Mar 2011
- Location
- New Zealand
- Posts
- 186
-
18th March 2013, 01:08 PM #19SENIOR MEMBER
- Join Date
- Aug 2008
- Location
- Normanhurst NSW 2076
- Age
- 81
- Posts
- 484
outboard turning
What I did to outboard turn was (2) things. I had a large alo gluechuck made up (120mm) with a left hand thread.
If I am using the supa nova chuck, I use a L Hand adaptor. I have found these two ways successful. I have found using
hot melt glue with the alo chuck very successful and to date I have not had any problems with this approach in
turning large bowls or platters (up to 400mm). I am about to go bigger with a large platter of monteray pine.
As you know, I am sure, keep the speed down, until you get it into balance and then in safe increments. I do not turn in reverse,
but some do, where they have ample room on both sides of the lathe. Drillit.
PS. I limit reverse to sanding.
-
18th March 2013, 03:27 PM #20Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Alo?
-
19th March 2013, 12:46 PM #21GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Nice range of speeds on the lathe. Did you fill the bed tubes with concrete, or did they come that way from the factory?
I have a Hegner with square steel tubes for the bed which shakes like a dog pooping peach seeds, and rings like a bell. I have considered drilling out the ends and filling the tubes with machine setting grout. Maybe even running a 5/8 inch rebar down the middle to stiffen things.
Yours looks like a nice stout lathe. What is the swing over the bed?So much timber, so little time.
Paul
-
19th March 2013, 08:36 PM #22Senior Member
- Join Date
- Mar 2011
- Location
- New Zealand
- Posts
- 186
Hi Paul,
The lathe came from the factory with the concrete in the tubes. The tubes are welded to 5 mm steel plate at the ends and I think the tubes are 4 or 5 mm wall thickness. I was told the concrete was to dampen vibration.
It will swing 50 cm (20 inches) over the bed and 80 cm (32 inches) outboard. The biggest piece I have had on it was about 40 cm (16 inches). It's not too bad as long as you keep the speed down until things are in balance.
Michael<!-- google_ad_section_end -->
-
20th March 2013, 02:20 AM #23GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Thanks Michael,
I tried to find more information on the lathe. I found two that were offered for sale in NZ, one with a photo on a rather spindly stand.So much timber, so little time.
Paul
Similar Threads
-
outboard turning bit
By bowl-basher in forum WOODTURNING - GENERALReplies: 3Last Post: 8th August 2010, 01:31 PM -
outboard turning
By bedecaner in forum WOODTURNING - GENERALReplies: 5Last Post: 19th August 2007, 11:07 PM -
outboard turning
By turnerted in forum WOODTURNING - GENERALReplies: 2Last Post: 31st October 2006, 03:56 PM -
Outboard turning on MC-900
By AdamJGS in forum WOODTURNING - GENERALReplies: 7Last Post: 12th November 2005, 01:00 AM -
Outboard Turning
By Rustic in forum WOODTURNING - GENERALReplies: 4Last Post: 8th November 2003, 04:12 PM