Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 23
Thread: Pro Disaster.
-
9th August 2012, 10:31 AM #1
Pro Disaster.
Many of us are scared of this happening it makes us think what can eventuate from this sort of thing.
His lathe has a guard many do not. I'd hate to have seen what could have happened if he had lowered the guard what direction and damage could that piece do then because it could not escape in the direction of forces natural.
I try reading each piece of timber I put on the lathe, I was taught by Darrell Smith at OTGA if its sus use a screw driver and see how much force is required to break it. If it can be salvaged with CA, epoxy or just glue then ok. If it breaks you have saved yourself a trip possibly to emergency.
This Pro should have used the screw driver method.
https://www.youtube.com/watch?v=FlhWF4M9CO4&feature
-
9th August 2012 10:31 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th August 2012, 11:21 AM #2
Ouch!!!!! There's leasons in that for all of us I think. I might have to actually use my face shield rather than just the safety specs.
-
9th August 2012, 12:13 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
As I have learned there are also face shields and there are face shields. While any face shield is better than none, the 2D curved shields are able to offer better protection than those curved in one direction.
Apart from the improved neck and chin protection provided by the 2D shields, the 1D shields are too easily able to be flatten and bend, even inwards, under heavy impact driving the shield into the operators face. The 2D curved shields will not deform anywhere near as easily and spread the load to the edges of the shield reducing the impact on any one point.
I experienced this when using a Chainsaw mill and a large 25 mm adjustment nut fell off the mil and landed on the chain moving at 60 mph. The nut struck me on the 1D curved face shield right between the eyes and the shield bent backwards and drove my prescription glasses into my face. It felt like I had been struck in the face by a cricket bat. On a 2D shield it would have just bounced off the structurally more rigid surface of the shield.
-
9th August 2012, 02:42 PM #4
Had more thought on his comment of a shield on the lathe.
If he had a large dia bowl or platter out board turning what shield would he have used then?
This video is a warning to myself also as I have some large 14"+ to 24" dia to do in the future.
-
9th August 2012, 04:56 PM #5Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
He didn't have the shield in place.
-
9th August 2012, 08:03 PM #6
Scary stuff
He could have saved it though. Clean up the rotten wood back to some solid stuff, then cast epoxy resin in the difference, or stabilise the rotten stuff and glue back up .Neil____________________________________________Every day presents an opportunity to learn something new
-
9th August 2012, 08:40 PM #7
Almost another statistc
Lucky, I don't think so. Crotch pieces are always risky. Unfortunately there have been at least 2 woodturners killed world wide in the past few years & possibly another young lady from Yale Uni, though its believed her fatal accident was incorrectly reported as wood turning. Then there are all the near misses...
-
9th August 2012, 09:16 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
-
10th August 2012, 09:00 AM #9
Not the best situation to have happen(I know a little bit understated) but at least he did not end up killing himself.
We would not have seen the results and would not be aware. I should say good on him for posting this.
-
11th August 2012, 02:13 PM #10
-
11th August 2012, 02:36 PM #11SENIOR MEMBER
- Join Date
- Apr 2007
- Location
- Perth
- Age
- 50
- Posts
- 728
Wow, I wasn't going to get a faceshield until a friend came over and helped me setup the lathe.
He suggested I get one, I thought about it for 2 secs and went and got one.......
-
11th August 2012, 09:09 PM #12
Good one Ray and a reminder to all of us.
Inspiration exists, but it has to find you working. — Pablo Picasso
-
11th August 2012, 09:25 PM #13.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
-
11th August 2012, 11:26 PM #14
+1 on the Armadillo, Meets high impact to AS1337. Great protection at arround $30, plus each bit is replaceable!
Protector Alsafe | Prosafe Face and Eye Protection
-
12th August 2012, 12:08 AM #15Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Similar Threads
-
What a disaster!!!
By jenlwren in forum WOODTURNING - PEN TURNINGReplies: 20Last Post: 27th July 2008, 12:46 PM -
Disaster
By aljenit in forum TRITON / GMCReplies: 9Last Post: 3rd March 2008, 08:20 PM -
Disaster with Epoxy - Help!
By steck in forum WOODWORK - GENERALReplies: 16Last Post: 20th February 2008, 04:33 PM -
Disaster!!
By hybridfiat in forum FINISHINGReplies: 15Last Post: 22nd December 2007, 01:29 PM -
Disaster! Disaster! Success.
By PenTurner in forum WOODTURNING - PEN TURNINGReplies: 10Last Post: 2nd December 2007, 11:54 AM