Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 23 of 23
Thread: A Question gor Gatiep
-
22nd September 2004, 10:22 PM #16Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Dan,
Glad but not surprised to hear it - good news! But you could get your retailer out to look at it rather than waiting til Dec. Who'd you buy it from?
Johnno - doesn't ring a bell with me but my hearing isn't as good as it used to be ;-}
CheersCheers, Ern
-
22nd September 2004 10:22 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
23rd September 2004, 12:49 AM #17A very trying Turner
- Join Date
- Dec 2003
- Location
- Bindoon Western Australia
- Age
- 78
- Posts
- 89
Ern
The retailer has offered for me to take my tailstock in and line it up on their showroom lathe to see if my tailstock is lower than theirs so it will at least give me a starting point. If it is not then I'll take the headstock in and by this method of ellimination I should be able to resolve the problem a lot sooner. To my simple mind the easist solution would be a replacement headstock and tailstock that match but then there may be other factors involved? it can't be the bed .... or can it....
Dan
-
23rd September 2004, 07:55 AM #18Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Good to hear things are moving Dan.
The bed is cast then machined, as are the head and tail stock mating surfaces, and no process is completely error free. Got a good straight edge to check the bed?
The headstock shaft and tailstock quill are bored for the morse taper, and again, only a minor error in this will give you a misalignment.
If you have or can borrow a morse taper extension, the method noted above of wax pencil resting on the tool rest and marking the extension as it's rotated in the main shaft will indicate whether there's any run out at that end.
Looking forward to the next episode }Cheers, Ern
-
23rd September 2004, 09:47 AM #19New Member
- Join Date
- Sep 2004
- Location
- Portsmouth UK
- Posts
- 1
mis-alighnment
Hi,
I may be stating the obvious but it is possible as its new that there is some foriegn matter between the head/tail stock and the bed?
Boots
-
23rd September 2004, 01:41 PM #20
Dan
Different lathe, but a suggestion worth looking at.
On the Teknatool site, they have a review on the Nova, done in the States, where they found the same problem, and it was traced to rubbish trapped in the packing grease between the swivel head and the lathe bed, as suggested below. Removing, cleaning with Kero, greasing and replacing solved the problem.
Worth a try. If they are physically of different heights, then it is a manufacturing fault that was not picked up before shipping, and they should be leant on to correct this immediately, not at their leisure!
Alastair
-
3rd November 2004, 01:33 AM #21A very trying Turner
- Join Date
- Dec 2003
- Location
- Bindoon Western Australia
- Age
- 78
- Posts
- 89
Mis-Aligned-Re-Aligned...
Thanks to all that took interest in my problem, I am happy to report that all has been corrected to my very great satisfaction...
Thanks to the supplier of my original lathe (who else but Carbatec Perth) I picked up a replacement yesterday which they gave ex their stock (to be replaced by Vicmarc) and it is spot on in every respect. I wish to publicly thank all of the staff at Carbatec Perth (without naming names as I am sure I would forget someone and end up in trouble) for all their patience in dealing with a westpest by name and nature. My thanks also to Vic at Vicmarc for the great after sales service and support. Needless to say I will be a lifelong customer of both of these establishments.
regards to all
Dan Faux
-
5th November 2004, 02:18 AM #22
Good one Dan....glad you got it sorted out.
I just looked back...................bad news make headlines! Wen you originally posted the bad news, there was 17 posts in 2 days. Its been two days since you posted the good outcome and not even a whisper! Amazing. Well let me say: Good on Carba-tec Perth and on Vicmarc for sorting the problem out! Hope you have many years of happy turning mate
-
5th November 2004, 04:50 AM #23
Dirty MT taper?
Just a shot, but I have heard of dirt getting into the Morse Taper causing mis-alighments.
Cheers!
John