Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 16
Thread: catches
-
2nd June 2013, 03:34 PM #1GOLD MEMBER
- Join Date
- Oct 2007
- Location
- vic clayton
- Posts
- 1,041
catches
Why is it, or is it just me , that the majority of catches seem to happen just as your finishing the piece and you go hmmm just need to take that little bit off there...catch.... arghh
Some people are like slinkies - not really good for anything, but they
bring a smile to your face when pushed down the stairs .
-
2nd June 2013 03:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd June 2013, 03:59 PM #2
Is that where those chips are coming from, they fly over my house?
Do mine make it from dandy to clayton as well.
Many many catches, and yep its always with that "I just need to take bit from.. B#&&3R".
-
2nd June 2013, 04:22 PM #3
We could blame Murphy but it could be we relax a bit and think we are finished.
RegardsHugh
Enough is enough, more than enough is too much.
-
2nd June 2013, 05:14 PM #4
Hmm. I am familiar with the concept.
Sometimes at the end we have swarf or chips etc which can add to the problem.
Secondly we have to remember the final cut has to be very light and often after being busy with the whole process this can be lost as the end arrives.
The other problem is that it can be the last cut with a blunt gouge. I will often stop and spend a bit of time getting the edge very sharp for the last cut or cuts. Quite often changing to another tool to achieve the final ie I have a 1/2 Thompson and a 1/2 Super Flute as my major work horses and finish the job always with one of two P&N 3/8 gouges.Inspiration exists, but it has to find you working. — Pablo Picasso
-
2nd June 2013, 06:02 PM #5Senior Member
- Join Date
- Jun 2012
- Location
- Mosgiel New Zealand
- Posts
- 221
Stop the lathe take a rest for a minuet a walk in the garden or just clean around the lathe it will take that built up mussel tension away and rest the eyes.But what do I know
Ian
-
2nd June 2013, 06:16 PM #6GOLD MEMBER
- Join Date
- Jan 2010
- Location
- Melbourne
- Posts
- 2,636
Hughie has nailed it. All too often we rush to get to the end point without thinking what it is we're actually try to achieve. I've completely slowed down my processes and added a little thinking time and the results have started to materialise. Mind you, a few pieces have been flung over the fence and into the paddock because of the dreaded catch
-Scott
-
2nd June 2013, 06:33 PM #7
hi guys,
yes, i think we can all relate to that at some time or another
like as has already been said ,go for a walk,clean up ,tea or coffee time
sharpen the tool, deep breath and away you go!!!!!!!!!
cheers smiife
-
2nd June 2013, 06:52 PM #8SENIOR MEMBER
- Join Date
- Feb 2008
- Location
- Nth of Newcastle
- Age
- 77
- Posts
- 811
I was told to stop the lathe......and go through the mistake with the chisel while your body remembers
what you just did........ better to learn from mistakes than keep repeating them.
That said I have at least my share of them.
-
2nd June 2013, 06:57 PM #9
I think it might be the last one because of the catch. I always say to myself one more cut even when I start the project.
-
2nd June 2013, 07:06 PM #10GOLD MEMBER
- Join Date
- Jun 2010
- Location
- shoalhaven n.s.w
- Posts
- 1,240
I. put it down to lack of concentration and so did the tradies I worked with! happens to us all! at Tafe we would make the noise of the skew catching and it would start a chain reaction around the room but for real! we got yelled at by class mates! was funny though! not so funny when customer supplies timber!
-
2nd June 2013, 07:41 PM #11SENIOR MEMBER
- Join Date
- Dec 2011
- Location
- Buderim qld
- Posts
- 842
If there is a positive, a catch and consequent resizing can improve on the original form.
-
4th June 2013, 06:11 AM #12GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
All of the above, and the more time spent at the lathe the less catches you will have.
I think the most important are to quit before you are tired, and to freshly sharpen and hone to razor sharpness before the final cuts.So much timber, so little time.
Paul
-
4th June 2013, 08:11 AM #13Senior Member
- Join Date
- Dec 2008
- Location
- Clarence Town
- Age
- 70
- Posts
- 217
-
4th June 2013, 11:06 AM #14
Up to a point......but this might explain why I keep producing miniature items
People think I'm in the business of making 1:72 scale models of real world objects.....
Reminds me of a project to build a metal toolbox at TAFE years ago, basically an exercise in bending and spot welding sheet steel. Perfectionist that I am, every tiny defect resulted in me changing the design, cutting the sheet down a bit, and starting again. Eventually I ended up with a beautifully crafted toolbox about the size of a sardine tin, not even big enough to hold a screwdriver...
-
4th June 2013, 11:56 AM #15Intermediate Member
- Join Date
- Mar 2013
- Location
- Illinois
- Posts
- 28
That is what seems to happen to me when i'am close to the end and i get in a bit of a hurry to finish up. Just walk away!
Similar Threads
-
Wooden catches
By Tiger in forum BOX MAKINGReplies: 10Last Post: 22nd February 2011, 12:00 PM -
Magnetic Box Catches
By Ronalene in forum BOX MAKINGReplies: 4Last Post: 24th November 2008, 11:25 PM -
catches!
By jimran in forum WOODTURNING - GENERALReplies: 16Last Post: 3rd March 2007, 04:33 PM -
Getting nasty catches on a bowl
By CameronPotter in forum WOODTURNING - GENERALReplies: 36Last Post: 23rd January 2006, 09:30 AM -
Cabinet catches.
By The Hornet in forum WOODWORK - GENERALReplies: 3Last Post: 17th April 2005, 10:40 PM