Thanks: 0
Needs Pictures: 0
Results 1 to 5 of 5
Thread: The Huon Trophy
-
2nd March 2021, 10:22 AM #1
The Huon Trophy
Over January our family helped lead a youth camp, in which we introduced a bunch of grade 9-12 kids to the fun of white-water kayaking over the course of a week. Toward the end of the camp we had a little accident, but before the evidence was discarded I snapped it up with the idea of using it to create a perpetual Huon Trophy.
Starting with an old Tasmanian Oak window lintel, I dressed, cut and glued it up into a block which would form the trophy base.
20210220_113001-1024x768.jpg 20210220_113546-1024x768.jpg 20210220_114239-1024x768.jpg 20210220_120501-scaled.jpg
Some rummaging about revealed a nearly perfectly sized scrap for the stem. It is a delicate balance when deciding what scrap to keep and what to discard of into the firewood pile. so when a smaller piece of retained scrap comes in handy it makes me feel as though I have the fulcrum optimally placed. I turned the stem to round, with a tenon on one end the same size as my largest forstner bit.
20210220_122904-scaled.jpg
It was then time to drill a matching hole in the base blank, trim the corners and glue in the stem to form the completed blank. Keen eyed readers may note that the orientation of the blank changed through this series of photos. Whilst drilling the hole I was in bowl blank mode, and forgot that it really needed to be in the spindle orientation to match the stem. I’m sure a more accomplished turner would have been able to happily cope with the changed grain orientation, but I chose to play it safe and re-drill the hole on the correct plane.
20210221_102839-scaled.jpg 20210221_110116-scaled.jpg 20210221_111448-scaled.jpg
The blank was now ready to turn. I mounted it in the lathe and with the slowest speed started roughing out the shape. This was the heaviest blank I’ve turned to date so it was with a little trepidation that I spun up that hunk of wood. In then end it wasn’t scary at all. Being reasonably well balanced, and with a heavy lathe bed it behaved very well. That being said, bone dry timber is hard going, and seemed to dull my chisels very quickly.
I really didn’t have much of an idea of what I was aiming for, and for a while kept changing and refining until finally the shape just sort of found itself. Phew, as I was hogging off a lot of wood in my deliberations! Lesson learned for next time: have a clear(er) idea of what you’re aiming for before you start.
20210221_123625-scaled.jpg 20210221_141707-scaled.jpg
And with that, all that was left was to sand, apply several coats of shellac and finish with wax. I bent a piece of aluminium bar to which I attached the helmet, and screwed to the top of the stem. As a finishing touch, I found some brass shim material and made the inaugural plaque, engraved with the Dremel, and screwed to the base. Thank goodness I have a bunch of tiny brass screws in my box making supplies jar.
20210227_125559-scaled.jpg 20210227_125906-scaled.jpg
All in all I was really pleased with how it turned out. It is the first time I’ve glued up multiple components to form a single blank, and apart form being more conscious of getting a better match between the base and stem, I’m chuffed. There is enough place for twenty plaques, so I don’t expect I’ll need to make another one until 2040.
Oh, and if you’ve ever considered white-water kayaking, your really should give it a go. It’s much safer than you think!
-
2nd March 2021 10:22 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd March 2021, 08:05 PM #2GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
Lance, very neat, but a question.
How are you driving the blank, you have a chuck, but I'm not sure if you have anything in the chuck driving, or are you gripping a short tenon?
Mick.
Ps: What do you call an old man in a kayak? Answer: A paddle pop!
-
3rd March 2021, 07:26 AM #3
Mick,
It is hard to see from my photos. I have my drive centre held in the chuck. Sometimes I do that if the chuck is already mounted as it is quicker than having to take the chuck off.
My decision to use the drive centre was two fold:
1. I was a little nervous with such a large glued-up blank, and figured that if something went terribly wrong (bad catch or split on the glue line) it would slip on the drive centre. A bit like a clutch. My centre has a long nose, so there's lots of centre in the piece before the teeth engage.
2. I needed to flip it end for end to clean up the base, and the drive centre simplified this.
I welcome any constructive critique of any of the above.
-
3rd March 2021, 08:14 AM #4
Lance
Lovely concept and good use of recycling ( Hold on, it was kayaking not cycling ). Anyhow, a good opportunity to use the newly refurbished lathe and test the boundaries. Nice job.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
3rd March 2021, 08:29 AM #5GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
Thanks for that Lance, I sort of figured that was how you did it, but I wasn't that sure.
Mick.
Similar Threads
-
Trophy Shield
By Ticky in forum WOODWORK - GENERALReplies: 2Last Post: 1st April 2014, 09:52 AM -
Another Trophy
By Willy Nelson in forum WOODTURNING - GENERALReplies: 3Last Post: 27th August 2013, 10:22 PM -
Rocket Trophy
By toddbron in forum WOODTURNING - GENERALReplies: 20Last Post: 23rd October 2011, 08:02 PM -
A Trophy I made...
By dnelson in forum WOODTURNING - GENERALReplies: 11Last Post: 15th January 2007, 12:59 PM -
Trophy cabinet
By kiwik in forum WOODWORK PICSReplies: 10Last Post: 30th June 2006, 10:04 AM